5秒后页面跳转
MG39U301ASC1 PDF预览

MG39U301ASC1

更新时间: 2022-02-26 14:06:07
品牌 Logo 应用领域
笙泉 - MEGAWIN /
页数 文件大小 规格书
12页 320K
描述
Open loop current peak detector

MG39U301ASC1 数据手册

 浏览型号MG39U301ASC1的Datasheet PDF文件第4页浏览型号MG39U301ASC1的Datasheet PDF文件第5页浏览型号MG39U301ASC1的Datasheet PDF文件第6页浏览型号MG39U301ASC1的Datasheet PDF文件第8页浏览型号MG39U301ASC1的Datasheet PDF文件第9页浏览型号MG39U301ASC1的Datasheet PDF文件第10页 
Buck Driver Example 2  
7 Application Information  
Input Voltage Regulator  
The MG39U301 integrates one high voltage regulator to generate the power for internal core logic. The  
internal power is taken from the AC line directly. Extra auxiliary transformer is not needed for the supply. When a  
voltage (7~500V) is applied at the VIN pin, the regulator maintains a constant 5.6V at the VDD pin. The VDD pin  
must be bypassed by a low ESR capacitor to provide a low impedance path for the high frequency current of the  
output date driver.  
Since the current driving capability of the regulator is limited to around 0.7mA. It’s not suitable for driving the  
external components. User must make sure the switching frequency should not be too high and the load at the  
GATE pin should not be too heavy.  
It’s recommended to add a series resistor between VINDC and VIN pin to protect the IC. Basically, several  
ten K to 100K ohms are recommended. The voltage drop on the resistor can be calculated as VRDROP = IOP x RVIN  
.
For large ILED application, it’s recommended to add a pull-high resistor (RP) between VINDC and VDD pin to  
provide more driving current.  
Selection of the Switching Control Scheme  
The MG39U301 provides two control schemes, constant frequency and constant off time. For a buck  
converter, the duty of PWM control signal is determined as D = VO / VIN, where VO is the voltage drop on LED  
strings (VLED). For a heavy load application (large VLED drop, D>0.45), user should select the constant off time  
mode.  
Selection of the Switching Frequency (FS)  
Rule of thumb, the range of 20KHz ~ 100KHz is recommended.  
For detail frequency setting, please check application note “AN_MG39U301_ROSC SEL”.  
GATE Output  
The GATE output of the MG39U301 is used to drive an external MOSFET. It is recommended that the gate  
charge QG of the external MOSFET should satisfy the equation as below:  
MEGAWIN  
MG39U301 Data Sheet  
7
 

与MG39U301ASC1相关器件

型号 品牌 描述 获取价格 数据表
MG39U301ASC2 MEGAWIN Open loop current peak detector

获取价格

MG3A JAUCH SMD Quartz Crystal

获取价格

MG400G1UL1 TOSHIBA TRANSISTOR 400 A, 450 V, NPN, Si, POWER TRANSISTOR, 2-109A1A, 5 PIN, BIP General Purpose P

获取价格

MG400H1FK1 TOSHIBA TRANSISTOR 400 A, 550 V, NPN, Si, POWER TRANSISTOR, 2-80D1A, 4 PIN, BIP General Purpose Po

获取价格

MG400H1FL1 TOSHIBA TRANSISTOR 400 A, 550 V, NPN, Si, POWER TRANSISTOR, 2-80D2A, 4 PIN, BIP General Purpose Po

获取价格

MG400H1UL1 TOSHIBA TRANSISTOR 400 A, 550 V, NPN, Si, POWER TRANSISTOR, 2-109A1A, 5 PIN, BIP General Purpose P

获取价格