MBRF1035 THRU MBRF1060
FEATURES
ITO-220AC
0.188 (4.77)
0.172 (4.36)
0.405 (10.27)
0.383 (9.72)
¨ Isolated plastic package has Underwriters Laboratory
0.110 (2.80)
0.100 (2.54)
Flammability Classifications 94V-0
¨ Metal silicon junction, majority carrier conduction
¨ Low power loss, high efficiency
0.131 (3.39)
0.122 (3.08)
0.140 (3.56)
0.130 (3.30)
DIA.
DIA.
¨ High current capability, low forward voltage drop
¨ High surge capability
¨ For use in low voltage, high frequency inverters,
free wheeling, and polarity protection applications
¨ Guardring for overvoltage protection
¨ High temperature soldering guaranteed:
250¡C/10 seconds, 0.25" (6.35mm) from case
0.600 (15.5)
0.580 (14.5)
0.350 (8.89)
0.330 (8.38)
0.676 (17.2)
0.646 (16.4)
PIN
1
2
0.191 (4.85)
0.171 (4.35)
0.110 (2.80)
0.100 (2.54)
0.560 (14.22)
0.530 (13.46)
0.060 (1.52)
MECHANICAL DATA
Case: JEDEC ITO-220AC fully overmolded plastic body
Terminals: Leads solderable per MIL-STD-750, Method 2026
Polarity: As marked
0.037 (0.94)
0.027 (0.69)
0.022 (0.55)
0.014 (0.36)
0.205 (5.20)
0.195 (4.95)
PIN 1
PIN 2
Mounting Position: Any
Mounting Torque: 5 in. - lbs. max.
Weight: 0.08 ounces, 1.81 grams
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25¡C ambient temperature unless otherwise specified.
SYMBOLS
VRRM
VRWM
VDC
MBRF1035
MBRF1045
MBRF1050
MBRF1060
UNITS
Volts
Volts
Volts
Maximum repetitive peak reverse voltage
Maximum working peak reverse voltage
Maximum DC blocking voltage
35
35
35
45
45
45
50
50
50
60
60
60
Maximum average forward rectified current
(SEE FIG. 1)
I(AV)
10.0
20.0
Amps
Amps
Peak repetitive forward current at TC=135¡C
(square wave 20 KHZ)
IFRM
Peak forward surge current
8.3ms single half sine-wave superimposed
on rated load (JEDEC Method)
IFSM
150.0
Amps
Peak repetitive reverse surge current (NOTE 1)
Voltage rate of change (rated VR)
IRRM
dv/dt
1.0
0.5
Amps
10,000
Vms
Maximum instantaneous
forward voltage at (NOTE 2) IF=10A, TC=125¡C
IF=20A, TC=25¡C
IF=10A, TC=25¡C
-
0.80
0.70
0.95
0.85
0.57
0.84
0.72
Volts
VF
IF=20A, TC=125¡C
Maximum instantaneous reverse current at rated
DC blocking voltage
TC= 25¡C
(NOTE 2) TC=125¡C
IR
0.10
15.0
mA
mA
Maximum thermal resistance, junction to case
Operating junction temperature range
Storage temperature range
RQJC
TJ
4.0
¡C/W
¡C
-65 to +150
-65 to +175
TSTG
¡C
RMS Isolation voltage from terminals to heatsink
with RH ² 30%
4500 (NOTE 3)
3500 (NOTE 4)
1500 (NOTE 5)
VISOL
Volts
NOTES:
(1) 2.0ms pulse width, f=1.0 KHZ
(2) Pulse test: 300ms pulse width, 1% duty cycle
(3) Clip mounting (on case), where lead does not overlap heatsink with 0.110Ó offset.
(4) Clip mounting (on case), where leads do overlap heatsink.
(5) Screw mounting with 4-40 screw, where washer diameter is £ 4.9 mm (0.19Ó).
2/18/99
www.kersemi.com