5秒后页面跳转
MAX15093 PDF预览

MAX15093

更新时间: 2024-11-06 02:52:59
品牌 Logo 应用领域
美信 - MAXIM /
页数 文件大小 规格书
9页 408K
描述
Banana Jacks for Input and Output Voltage

MAX15093 数据手册

 浏览型号MAX15093的Datasheet PDF文件第2页浏览型号MAX15093的Datasheet PDF文件第3页浏览型号MAX15093的Datasheet PDF文件第4页浏览型号MAX15093的Datasheet PDF文件第5页浏览型号MAX15093的Datasheet PDF文件第6页浏览型号MAX15093的Datasheet PDF文件第7页 
Evaluate: MAX15093/MAX15093A  
MAX15093/MAX15093A  
Evaluation Kits  
General Description  
Quick Start  
The MAX15093/MAX15093A evaluation kits (EV kits)  
provide a proven design to evaluate the MAX15093/  
MAX15093A hot-swap controllers with an integrated 15A  
MOSFET. The EV kits are configured to pass 15A in a  
2.7V to 18V hot-swap application, thus providing a fully  
integrated solution. The EV kits use the MAX15093GWL+/  
MAX15093AGWL+T in a 2.57mm x 4.03mm, 40-bump,  
0.5mm pitch wafer-level package (WLP) with a proven  
four-layer PCB design. As configured, the EV kits are  
optimized to operate at 12V.  
Required Equipment  
MAX15093 or MAX15093A EV kit  
12V, 15A DC power supply  
Voltmeter  
Procedure  
The EV kits are fully assembled and tested. Follow the  
steps below to verify board operation. Caution: Do not  
turn on the power supply until all connections are  
completed.  
The two EV kit versions (MAX15093AEVKIT# and  
MAX15093EVKIT#) are built on the same PCB fabrication  
and can be used interchangeably to evaluate either the  
MAX15093 or MAX15093A by replacing U1 with the  
desired device.  
1) Verify that a shunt is installed across pins 1-2 on the  
following jumpers: J1, J3, J4, J5, UV_IN, and CB.  
2) Turn on the power supply and set the supply to 12V,  
then disable the power supply.  
3) Connect the positive terminal of the power supply  
to the IN banana jack on the EV kits. Connect the  
negative terminal of the power supply to the GND  
banana jack.  
Features  
2.7V to 18V Operating-Voltage Range  
Up to 15A Configurable Load-Current Capability  
Banana Jacks for Input and Output Voltage  
Programmable Slew-Rate Control  
Selectable/Configurable Circuit-Breaker Threshold  
Configurable Overvoltage/Undervoltage Lockout  
Programmable Timeout Delay  
4) Enable the power supply.  
5) Verify that the voltage between the OUT and GND  
banana jacks is 12V.  
6) Verify that the internal regulator voltage (REG) is 3.3V.  
7) The EV kits are now ready for additional evaluation.  
FAULT and PG Outputs  
Defined Safe Operation Area  
Proven PCB Layout  
Ordering Information appears at end of data sheet.  
Fully Assembled and Tested  
19-8764; Rev 1; 7/19  

与MAX15093相关器件

型号 品牌 获取价格 描述 数据表
MAX15093A MAXIM

获取价格

Banana Jacks for Input and Output Voltage
MAX15093A ADI

获取价格

具有电流报告输出的2.7V至18V、15A、热插拔解决方案
MAX15093AEVKIT MAXIM

获取价格

Banana Jacks for Input and Output Voltage
MAX15093AGWL+T MAXIM

获取价格

Power Supply Support Circuit,
MAX15095 MAXIM

获取价格

2.7V to 18V Operating Voltage Range
MAX15095 ADI

获取价格

2.7V至18V、6.6A、集成热插拔/电子断路器
MAX15095A MAXIM

获取价格

2.7V to 18V Operating Voltage Range
MAX15095A ADI

获取价格

2.7V至18V、6.6A、集成热插拔/电子断路器
MAX15095AEVKIT MAXIM

获取价格

2.7V to 18V Operating Voltage Range
MAX15095AGFC+ MAXIM

获取价格

Power Management Circuit,