Datasheet > MAX149X2EVKIT

MAX149X2EVKIT

更新时间： 2024-09-13 02:51:03

品牌	Logo	应用领域
美信 - MAXIM		/
页数	文件大小	规格书
13页	3442K
描述
Terminal Block Connectors for Easy RS-485/ PROFIBUS Evaluation

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

MAX149X2EVKIT 数据手册

Evaluates: MAX14940/MAX14943/

MAX14946/MAX14949

MAX149X2 Evaluation Kit

General Description

Quick Start

The MAX149X2 evaluation kit (EV kit) is a fully assembled

and tested PCB that demonstrates the functionality of the

MAX14943 isolated RS-485/PROFIBUS transceiver. The

EV kit operates from a single 3.3V supply and features an

on-board isolated power supply to power the secondary-

side of the circuit.

Required Equipment

● MAX149X2 EV kit

● 3.3V, 1A DC power supply

● Signal/function generator

● Oscilloscope

Startup Procedure

The EV kit is fully assembled and tested. Follow the steps

below to verify board operation:

The MAX149X2 EV kit comes with the MAX14943GWE+

installed, but can also be used to evaluate the pin-compatible

MAX14940, MAX14946, and MAX14949 ICs.

1) Set the DC power supply to 3.3V and connect the

DC power supply between the EV kits VDDA and

GNDA connectors of the EV kit.

Features

● Operates from a Single 3.3V Supply

2) Ensure that J2 and J3 are in their default positions

(see Table 1).

3) Turn on the power supply.

4) Set the signal/function generator to output a 100kHz

0 to 3V square wave. Note: Set the signal/function

generator to operate with a high-impedance load. If

needed, the R1 pad is available to add a 50Ω impedance

to ground.

● Terminal Block Connectors for Easy RS-485/

PROFIBUS Evaluation

● 5000V

Isolation for 60s

RMS

● Fully Assembled and Tested

● Proven PCB Layout

Ordering Information appears at end of data sheet.

5) Connect the signal/function generator to the TXD

test point.

6) Verify that the A and B outputs switch as the signal

toggles.

Table 1. Jumper Settings (J1–J6)

JUMPER

SHUNT POSITION

DESCRIPTION

1-2

2-3*

Receiver is disabled. RXD is high impedance.

Receiver is enabled. RXD is active.

1-2*

Driver is enabled. DEM is high.

2-3

Driver is disabled. DEM is low.

Open*

Closed

Open*

Closed

DE and RE are not connected together.

DE and RE are connected together.

A and B are not connected through the on-board 120Ω resistor.

Connects the on-board 120Ω resistor between A and B.

*Default position.

19-7646; Rev 0; 6/15

12 3 4 5 6 7...13

中文翻译

下载PDF

与MAX149X2EVKIT相关器件

型号	品牌	获取价格	描述	数据表
MAX150	MAXIM	获取价格	CMOS High Speed 8Bit A/D Converter with Refrence and Track/Hold Function
MAX150	ADI	获取价格	CMOS、1.3μs、8位ADC，带有电压基准和采样/保持
MAX15000	MAXIM	获取价格	Current-Mode PWM Controllers with Programmable Switching Frequency
MAX15000	ADI	获取价格	电流模式PWM控制器，可调节开关频率
MAX15000A	MAXIM	获取价格	Current-Mode PWM Controllers with Programmable Switching Frequency
MAX15000AEUB+	MAXIM	获取价格	Current-Mode PWM Controllers with Programmable Switching Frequency
MAX15000B	MAXIM	获取价格	Current-Mode PWM Controllers with Programmable Switching Frequency
MAX15000BEUB+	MAXIM	获取价格	Current-Mode PWM Controllers with Programmable Switching Frequency
MAX15001	MAXIM	获取价格	Current-Mode PWM Controllers with Programmable Switching Frequency
MAX15001	ADI	获取价格	电流模式PWM控制器，可调节开关频率

与MAX149X2EVKIT相关文章

SL74HC10N：高性能三输入与非门解析
2024-09-03

77
AIC1781A 电池充电控制器深度解析
2024-09-03

67
Pickering新高压舌簧继电器亮相汽车测试博览会
2024-08-26

97
采用MCU+MPU双处理器架构实现的创新应用设计探索
2024-08-23

109

产品中心

服务支持

精选活动

关于我们

帮助中心

MAX149X2EVKIT

MAX149X2EVKIT 数据手册

与MAX149X2EVKIT相关器件

与MAX149X2EVKIT相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

MAX149X2EVKIT

MAX149X2EVKIT 数据手册

与MAX149X2EVKIT相关器件

与MAX149X2EVKIT相关文章

您还可以找

您在本页遇到什么问题？