Support &
Community
Reference
Design
Product
Folder
Order
Now
Tools &
Software
Technical
Documents
LM5141-Q1
SNVSAJ6D –JULY 2016–REVISED DECEMBER 2017
LM5141-Q1 Wide Input Range Synchronous Buck Controller
1 Features
2 Applications
1
•
•
Qualified for Automotive Applications
•
Automotive Applications Including:
AEC-Q100 Qualified With the Following Results:
–
–
–
Infotainment Systems
–
Device Temperature Grade 1: –40°C to
+125°C Ambient Operating Temperature
Instrumentation Clusters
Advanced Driver Assistance Systems (ADAS)
–
–
Device HBM ESD Classification Level 2
Device CDM ESD Classification Level C4B
3 Description
The LM5141-Q1 is a synchronous buck controller,
intended for high voltage wide VIN step-down
converter applications. The control method is peak
current mode control. Current mode control provides
inherent line feed-forward, cycle-by-cycle current
limiting, and ease-of-loop compensation. The
LM5141-Q1 features slew rate control to simplify the
compliance with CISPR and automotive EMI
requirements.
•
•
VIN: 3.8 V to 65 V (70 V Absolute Maximum)
Output: Fixed 3.3 V, 5 V, or Adjustable From
1.5 V to 15 V with ±0.8% Accuracy
•
•
•
Fixed 2.2-MHz or 440-kHz Switching Frequency
with ±5% Accuracy
High-Side and Low-Side Gate Drive With Slew-
Rate Control
Optional Frequency Shift by Varying an Analog
Voltage or RT Resistor
The LM5141-Q1 has two selectable switching
frequencies: 2.2 MHz and 440 kHz. Gate drivers with
slew rate Control that can be adjusted to reduce EMI.
•
•
•
•
•
Optional Synchronization to an External Clock
Optional Spread Spectrum
In light or no-load conditions, the LM5141-Q1
operates in skip cycle mode for improved low power
efficiency. The LM5141-Q1 has a high voltage bias
regulator with automatic switch-over to an external
bias to reduce the IQ current from VIN. Additional
features include frequency synchronization, cycle-by-
cycle current limit, hiccup mode fault protection for
sustained overload, and power good output.
Shutdown Mode IQ: 10 µA Typical
Low Standby Mode IQ: 35 µA Typical
75-mV Current Limit Threshold with ±0.9%
Accuracy
•
•
•
•
•
External Resistor or DCR Current Sensing
Output Enable Logic Input
Hiccup Mode for Sustained Overload
Power-Good Indication Output
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
Selectable Diode Emulation or Forced Pulse-
Width Modulation
LM5141-Q1
VQFN (24)
4.00 mm × 4.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
•
•
24-pin VQFN Package With Wettable Flanks
Create a Custom Design Using the LM5141-Q1
With the WEBENCH® Power Designer
Simplified Schematic
VIN
CIN
VIN
VCC
CVCC
DBST
CBST
HB
HO
RES
SS
LOUT
VOUT
HOL
SW
RSENSE
DITH
LM5141-Q1
COUT
LO
CRES
CSS
CDITH
LOL
PGND
PG
CS
EN
DEMB
VOUT
VCCX
RCOMP CCOMP
COMP
FB
AGND
RT
OSC VDDA
RT
CVDDA
Copyright © 2016, Texas Instruments Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.