Datasheet
LM393xxx LM339xxx LM2903xxx LM2901xxx
LM339F, LM2901F
LM339FJ, LM2901FJ
LM339FV, LM2901FV
: SOP14
: SOP-J14
: SSOP-B14
LM339FVJ, LM2901FVJ : TSSOP-B14J
Pin No.
Pin Name
1
2
OUT2
OUT1
VCC
-IN1
OUT2
OUT1
OUT3
OUT4
1
2
14
13
3
4
5
+IN1
-IN2
12
11
10
9
VCC
-IN1
+IN1
3
4
5
VEE
+IN4
6
CH1
CH4
7
+IN2
-IN3
-
+
-
+
8
-IN4
9
+IN3
-IN4
10
11
12
13
14
-IN2
6
7
+IN3
-IN3
CH3
-
CH2
+IN4
VEE
-
+
+
+IN2
8
OUT4
OUT3
Absolute Maximum Ratings (TA=25°C)
Parameter
Rating
Symbol
VCC-VEE
Unit
LM393xxx
LM339xxx LM2903xxx LM2901xxx
Supply Voltage
+36
V
0.68(Note 1,9)
0.67(Note 2,9)
0.62(Note 3,9)
0.62(Note 3,9)
0.58(Note 4,9)
0.58(Note 4,9)
-
0.68(Note 1,9)
0.67(Note 2,9)
0.62(Note 3,9)
0.62(Note 3,9)
SOP8
-
-
-
SOP-J8
SSOP-B8
TSSOP-B8
TSSOP-B8J
MSOP8
SOP14
-
-
-
-
-
0.58(Note 4,9)
-
Power Dissipation
PD
W
-
0.58(Note 4,9)
-
-
-
-
-
0.56(Note 5,9)
1.02(Note 6,9)
0.87(Note 7,9)
0.85(Note 8,9)
-
-
-
-
0.56(Note 5,9)
1.02 (Note 6,9)
0.87(Note 7,9)
0.85(Note 8,9)
SOP-J14
SSOP-B14
TSSOP-B14J
VID
Differential Input Voltage (Note 10)
Common-mode Input Voltage range
Input Current(Note 11)
+36
V
V
VICM
(VEE-0.3) to (VEE+36)
-10
II
mA
Single Supply
Dual Supply
Topr
+3.0 to +32.0
Vopr
Operating Supply Voltage
V
±1.5 to ±16.0
Operating Temperature Range
Storage Temperature Range
Maximum Junction Temperature
-40 to +85
-40 to +125
°C
°C
°C
Tstg
-55 to +150
+150
Tjmax
(Note 1) Reduce 5.5mW per 1°C above 25°C.
(Note 2) Reduce 5.4mW per 1°C above 25°C.
(Note 3) Reduce 5.0mW per 1°C above 25°C.
(Note 4) Reduce 4.7mW per 1°C above 25°C.
(Note 5) Reduce 4.5mW per 1°C above 25°C.
(Note 6) Reduce 8.2mW per 1°C above 25°C.
(Note 7) Reduce 7.0mW per 1°C above 25°C.
(Note 8) Reduce 6.8mW per 1°C above 25°C.
(Note 9) Mounted on an FR4 glass epoxy PCB 70mm×70mm×1.6mm (Copper foil area less than 3%).
(Note 10) Differential Input Voltage is the voltage difference between the inverting and non-inverting inputs. The input pin voltage is set to more than VEE
.
(Note 11) An excessive input current will flow when input voltages of less than VEE-0.6V are applied.
The input current can be set to less than the rated current by adding a limiting resistor.
Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is
operated over the absolute maximum ratings.
www.rohm.com
TSZ02201-0GOG0G200770-1-2
15.Jul.2016 Rev.002
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
2/37