®
EZ-LIGHT K50 and K80 Specialty — 3-Color
Datasheet
Compact, single-point devices for error-proofing of bin-picking operaꢀons
•
Rugged, cost-eꢁecꢀve, and easy-to-install soluꢀons for error-proofing and parts-
verificaꢀon applicaꢀons
•
•
•
•
•
Compact devices are completely self-contained - no controller needed
Illuminated dome provides a big, easy-to-see green, red or yellow job light
Push-buꢂon and passive-actuaꢀon models available
Choose NPN or PNP output, depending on model
Fully encapsulated IP67 construcꢀon — ideal for use in abusive environments; rated to
IP69K, depending on installaꢀon; see specificaꢀons
•
•
•
Immune to ambient light, EMI, and RFI interference
12 to 30 V dc operaꢀon
5-pin M12 PUR pigtail (150 mm) with quick disconnect fiꢃng
WARNING: Not To Be Used for Personnel Protecꢀon
Never use this device as a sensing device for personnel protecꢀon. Doing so could lead to serious injury or
death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel
safety applicaꢀons. A sensor failure or malfuncꢀon can cause either an energized or de-energized sensor output
condiꢀon.
Models
1
2
Model
Sensing Mode / LED
Housing
Range
2 m (6 ꢅ)
Output
Job Light
K50RPLPGRYC3QPMA
K50RPLPGRYC4QPMA
PNP,
Polarized retroreꢄecꢀve,
visible red, 680 nm
normally
closed
K50APFF50GRYC3QPMA
K50APFF50GRYC4QPMA
50 mm cutoꢁ
50 mm dome
30 mm mount
polycarbonate
Fixed field, infrared, 880
nm
Green/
yellow/
red
K50APFF100GRYC3QPMA
K50APFF100GRYC4QPMA
K50APPBGRYC3QPMA
K50APPBGRYC4QPMA
K80APPBGRYC3QPMA
K80APPBGRYC4QPMA
100 mm cutoꢁ
PNP,
normally
open
—
Push buꢂon
50 mm dome
Flat or DIN- mount
polycarbonate
A model with a quick disconnect fiꢃng requires a maꢀng cable (see Accessories on page 4).
Overview
The solid-state output interfaces to a system controller, which is pre-programmed for a specific sequence of tasks. Mounted in or near
each bin in an assembler’s work staꢀon, the sensor job light signals the assembler:
•
•
Which bins contain items to be picked in a given operaꢀon; and
In what order they should be picked.
As the assembler takes a part in sequence and pushes the buꢂon, the sensor senses that the part was removed and sends an output
signal to the controller. The controller verifies if the correct part was taken and may respond by turning that job light OFF, acꢀvaꢀng the
job light of the next bin in the sequence.
1
2
The 5-pin 150 mm M12/Euro-style PUR pigtail quick disconnect models are listed.
•
•
•
To order the 2 m (6 ꢅ) PVC cable model, omit the suffix “QPMA” from the model number (e.g., “K50RPLPGRYC3”).
To order the 9 m (30 ꢅ) PVC cable model, replace the suffix “QPMA” with “W/30” (e.g., “K50RPLPGRYC3 W/30”).
To order the 150 mm (5.9 in) PVC pigtail with 5-pin M12/Euro-style fiꢃng, replace the suffix “QPMA” with “QP” (e.g., “K50RPLPGRYC3QP”).
PNP models only are listed. For other output types, contact the Factory.
Original Document
137551 Rev. E
8 February 2017
137551