Sample &
Buy
Support &
Community
Product
Folder
Tools &
Software
Technical
Documents
ISO5451
SLLSEO1B –JUNE 2015–REVISED DECEMBER 2015
ISO5451 High-CMTI 2.5-A / 5-A Isolated IGBT, MOSFET Gate Driver
with Active Safety Features
1 Features
3 Description
The ISO5451 is a 5.7-kVRMS, reinforced isolated gate
1
•
50-kV/μs Minimum and 100-kV/μs Typical
Common-Mode Transient Immunity (CMTI)
at VCM = 1500 V
driver for IGBTs and MOSFETs with 2.5-A source
and 5-A sink current. The input side operates from a
single 3-V to 5.5-V supply. The output side allows for
a supply range from minimum 15-V to maximum
30-V. Two complementary CMOS inputs control the
output state of the gate driver. The short propagation
time of 76 ns assures accurate control of the output
stage.
•
•
2.5-A Peak Source and 5-A Peak Sink Currents
Short Propagation Delay: 76 ns (Typ),
110 ns (Max)
•
•
•
2-A Active Miller Clamp
Output Short-Circuit Clamp
An internal desaturation (DESAT) fault detection
recognizes when the IGBT is in an overload
condition. Upon a DESAT detect the gate driver
output is driven low to VEE2 potential turning the IGBT
immediately off.
Fault Alarm upon Desaturation Detection is
Signaled on FLT and Reset Through RST
•
•
Input and Output Under Voltage Lock-Out (UVLO)
with Ready (RDY) Pin Indication
Active Output Pull-down and Default Low Outputs
with Low Supply or Floating Inputs
When desaturation is active, a fault signal is sent
across the isolation barrier pulling the FLT output at
the input side low and blocking the isolator input. The
FLT output condition is latched and can be reset
through a low-active pulse at the RST input.
•
•
•
•
3-V to 5.5-V Input Supply Voltage
15-V to 30-V Output Driver Supply Voltage
CMOS Compatible Inputs
When the IGBT is turned off during normal operation
with bipolar output supply, the output is hard clamp to
VEE2. If the output supply is unipolar, an active Miller
clamp can be used, allowing Miller current to sink
across a low impedance path preventing IGBT to be
dynamically turned on during high voltage transient
conditions.
Rejects Input Pulses and Noise Transients
Shorter Than 20 ns
•
•
•
Operating Temperature: –40°C to 125°C Ambient
Isolation Surge Withstand Voltage 10000-VPK
Safety and Regulatory Certifications:
–
8000-VPK VIOTM and 1420-VPK VIORM
Reinforced Isolation per DIN V VDE V 0884-10
(VDE V 0884-10):2006-12
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
–
–
5700-VRMS Isolation for 1 Minute per UL 1577
ISO5451
SOIC (16)
10.30 mm × 7.50 mm
CSA Component Acceptance Notice 5A, IEC
60950-1, IEC 60601-1 and IEC 61010-1 End
Equipment Standards
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Functional Block Diagram
–
–
CQC Certification per GB4943.1-2011
All Certifications are Planned
2 Applications
•
Isolated IGBT and MOSFET Drives in
–
–
–
–
–
Industrial Motor Control Drives
Industrial Power Supplies
Solar Inverters
L{h5451
OUT
HEV and EV Power Modules
Induction Heating
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.