HIP6303
Data Sheet
December 1999
File Number 4767
Microprocessor CORE Voltage Regulator
Multi-Phase Buck PWM Controller
Features
• AMD Athlon Compatible
The HIP6303 multi-phase PWM control IC together with its
companion gate drivers, the HIP6601, HIP6602 or HIP6603
and Intersil MOSFETs provides a precision voltage
regulation system for advanced microprocessors.
• Multi-Phase Power Conversion
• Precision Channel Current Sharing
- Loss Less Current Sampling - Uses r
DS(ON)
Multiphase power conversion is a marked departure from
earlier single channel converter configurations previously
employed to satisfy the ever increasing current demands of
modern microprocessors. Multi-phase converters, by
distributing the power and load current results in smaller and
lower cost transistors with fewer input and output capacitors.
These reductions accrue from the higher effective
conversion frequency with higher frequency ripple current
due to the phase interleaving process of this topology. For
example, a three channel converter operating at 350kHz will
have a ripple frequency of 1.05MHz. Moreover, greater
converter bandwidth of this design results in faster response
to load transients.
• Precision CORE Voltage Regulation
- ±1% System Accuracy Over Temperature
• Microprocessor Voltage Identification Input
- 4-Bit VID Input
- 1.30V to 2.05V in 50mV Steps
- Programmable “Droop” Voltage
• Fast Transient Recovery Time
• Over Current Protection
• Automatic Selection of 2, 3, or 4 Channel Operation
• High Ripple Frequency, (Channel Frequency) Times
Number of Channels . . . . . . . . . . . . . . . 100kHz to 6MHz
Outstanding features of this controller IC include
Ordering Information
programmable VID codes from the microprocessor that
range from 1.30V to 2.05V with a system accuracy of ±1%.
Pull up currents on these VID pins eliminates the need for
external pull up resistors. In addition “droop” compensation,
used to reduce the overshoot or undershoot of the CORE
voltage, is easily programmed with a single resistor.
o
PART NUMBER
TEMP. ( C)
PACKAGE
PKG. NO.
HIP6303CB
0 to 70
20 Ld SOIC
M20.3
HIP6303CB-T
HIP6303EVAL1
20 Ld SOIC Tape and Reel
Evaluation Platform
Another feature of this controller IC is the PGOOD monitor
circuit which is held low until the CORE voltage increases,
during its Soft-Start sequence, to within 10% of the
programmed voltage. Over-voltage, 15% above programmed
CORE voltage, results in the converter shutting down and
turning the lower MOSFETs ON to clamp and protect the
microprocessor. Under voltage is also detected and results
in PGOOD low if the CORE voltage falls 10% below the
programmed level. Over-current protection reduces the
regulator current to less than 25% of the programmed trip
value. These features provide monitoring and protection for
the microprocessor and power system.
Pinout
HIP6303 (SOIC)
TOP VIEW
1
2
20
19
18
17
16
15
14
13
12
11
VID3
V
CC
VID2
VID1
VID0
EN
PGOOD
PWM4
ISEN4
ISEN1
PWM1
PWM2
ISEN2
ISEN3
PWM3
3
4
5
6
COMP
FB
7
8
FS/DIS
GND
VSEN
9
10
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999
Athlon™ is a trademark of Advanced Micro Devices, Inc.
1
5秒后页面跳转
AO3401场效应管参数、引脚图、应用原理图
BT131可控硅参数及引脚图、工作原理详解
74LS32芯片参数、引脚图及功能真值表
全球首块英伟达H200交付 黄仁勋“送货上门”
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
