USB-Compliant Single-Cell
Li-Ion Switching Charger
with USB-OTG Boost for
200 mA to 1.45 A Systems
FAN54005
Description
The FAN54005 is a highly integrated switch−mode
charger, configurable for 200 mA to 1.45 A systems using
a single external resistor.
www.onsemi.com
The charging parameters and operating modes are program−
2
mable through an I C Interface that operates up to 3.4 Mbps.
1
The charger and boost regulator circuits switch at 3 MHz
to minimize the size of external passive components.
The FAN54005 provides battery charging in three phases:
conditioning, constant current and constant voltage.
To ensure USB compliance and minimize charging time, the
WLCSP
20 BALL
CASE 567SL
2
input current limit can be changed through the I C interface
• Charge Parameters Programmable through High−Speed
by the host processor. Charge termination is determined by
a programmable minimum current level. A safety timer with
2
I C Interface (3.4 Mb/s) with Fast Mode Plus
Compatibility
♦ Input Current
2
reset control provides a safety backup for the I C host.
2
Charge status is reported to the host through the I C port.
♦ Fast−Charge / Termination Current
♦ Charger Voltage
The integrated circuit (IC) automatically restarts the charge
cycle when the battery falls below an internal threshold. If
the input source is removed, the IC enters a high−impedance
mode, preventing leakage from the battery to the input.
Charge current is reduced when the die temperature reaches
120°C, protecting the device and PCB from damage.
The FAN54005 can operate as a boost regulator on
command from the system. The boost regulator includes a
soft−start that limits inrush current from the battery and uses
the same external components used for charging the battery.
♦ Termination Enable
• 3 MHz Synchronous Buck PWM Controller with Wide
Duty Cycle Range
• Small Footprint 1 mH External Inductor
• Safety Timer with Reset Control
• 1.8 V Regulated Output from VBUS for Auxiliary Circuits
• Dynamic Input Voltage Control Automatically Reduces
Charging Current with Weak Input Sources
• Low Reverse Leakage to Prevent Battery Drain to VBUS
• 5 V, 500 mA Boost Mode for USB OTG for 3.0 V to
4.5 V Battery Input
Features
• Fully Integrated, High−Efficiency Charger for
Single−Cell Li−Ion and Li−Polymer Battery Packs
• Charge Voltage Accuracy: 0.5% at 25°C
Charge Voltage Accuracy: 1% from 0 to 125°C
• Available in a 1.96 x 1.87 mm, 20−bump, 0.4 mm Pitch
WLCSP Package
• Supports 200 mA to 1.45 A Systems
95% Efficiency for 200 mA−Hour Batteries
94% Efficiency for 500 mA−Hour Batteries
90% Efficiency for 1.0 A−Hour Batteries
Applications
• Wireless Speakers, Headphones
• Cell Phones, Gaming Devices
• Toys, Drones, Digital Cameras
• IoT Devices
•
•
5% Input Current Regulation Accuracy
5% Charge Current Regulation Accuracy
• 20 V Absolute Maximum Input Voltage
• 6 V Maximum Input Operating Voltage
• E−Cigs, Vapes
ORDERING INFORMATION
†
Part Number
Temperature Range
Package
PN Bits: IC_INFO[4:2]
Packing
FAN54005UCX
−40°C to +85°C
20−Bump, Wafer−Level Chip−Scale Package
(WLCSP), 0.4 mm Pitch, 1.96 x 1.87 mm
101
Tape and Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
© Semiconductor Components Industries, LLC, 2015
1
Publication Order Number:
November, 2019 − Rev. 4
FAN54005/D