Full/Low Speed USB Digital Isolator
ADuM4160
FEATURES
FUNCTIONAL BLOCK DIAGRAM
USB 2.0 compatible
Low and full speed data rate: 1.5 Mbps and 12 Mbps
Bidirectional communication
1
2
3
16
15
14
V
V
REG
REG
BUS1
BUS2
GND
GND
1
2
V
V
DD2
DD1
Short-circuit protection for xD+ and xD− lines
3.3 V and 5 V (dual mode power configuration) operation
7 mA maximum upstream supply current @ 1.5 Mbps
8 mA maximum upstream supply current @ 12 Mbps
2.3mA maximum upstream idle current
Class 3A contact ESD performance per ANSI/ESD STM5.1-2007
High temperature operation: 105°C
4
5
13
12
PDEN
SPU
SPD
PIN
6
11
UD–
UD+
DD–
7
8
10
9
DD+
GND
GND
1
2
PU LOGIC
PD LOGIC
High common-mode transient immunity: >25 kV/μs
16-lead SOIC wide-body package
RoHS compliant
Safety and regulatory approvals
UL recognition: 5000 V rms for 1 minute per
UL 1577 (pending)
CSA Component Acceptance Notice #5A
IEC 60601-1: 125 V rms (reinforced)
IEC 60950-1: 380 V rms (reinforced)
VDE certificate of conformity (pending)
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12
Figure 1.
Many microcontrollers implement USB so that it presents only
the D+ and D− lines to external pins. This is desirable in many
cases because it minimizes external components and simplifies
the design; however, this presents particular challenges when
isolation is required. USB lines must automatically switch between
actively driving D+/D−, receiving data, and allowing external
resistors to set the idle state of the bus. The ADuM4160 provides
mechanisms for detecting the direction of data flow and control
over the state of the output buffers. Data direction is determined
on a packet-by-packet basis.
V
IORM = 846 V peak
The ADuM4160 uses the edge detection based iCoupler tech-
nology in conjunction with internal logic to implement a
transparent, easily configured, upstream facing port isolator.
Isolating an upstream facing port provides several advantages
in simplicity, power management, and robust operation.
APPLICATIONS
USB peripheral isolation
Isolated USB hub
GENERAL DESCRIPTION
The ADuM41601 is a USB port isolator, based on Analog Devices,
Inc., iCoupler® technology. Combining high speed CMOS and
monolithic air core transformer technology, these isolation
components provide outstanding performance characteristics
and are easily integrated with low and full speed USB-compatible
peripheral devices.
The isolator has propagation delay comparable to that of a
standard hub and cable. It operates with the supply voltage
on either side ranging from 3.1 V to 5.5 V, allowing connection
directly to VBUS by internally regulating the voltage to the signaling
level. The ADuM4160 provides isolated control of the pull-up
resistor to allow the peripheral to control connection timing.
The device has a low idle current; a suspend mode is required.
1 Protected by U.S. Patents 5,952,849; 6,873,065; 7,075,329. Other patents pending.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks are theproperty of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2009 Analog Devices, Inc. All rights reserved.