5秒后页面跳转
EL6283C PDF预览

EL6283C

更新时间: 2024-11-17 23:14:47
品牌 Logo 应用领域
ELANTEC 振荡器驱动器二极管激光二极管放大器PC
页数 文件大小 规格书
2页 43K
描述
3-Channel Laser Diode Driver w/Oscillator & APC Amplifier

EL6283C 数据手册

 浏览型号EL6283C的Datasheet PDF文件第2页 
EL6283C - Product Brief  
3-Channel Laser Diode Driver w/Oscillator & APC Amplifier  
Features  
General Description  
Shrink-Small Outline Package  
The EL6283C is a high-performance three channel laser driver that  
provides controlled current to a grounded laser diode. Write channels  
2 and 3 can provide up to 200mA per channel of DC or pulsed current,  
with switching speeds of approximately one nanosecond rise/fall time.  
All three channels are summed together at the IOUT output, allowing  
the user to create multilevel waveforms in order to optimize laser  
diode performance. The level of the output current is set by an analog  
voltage applied to an external resistor which converts the voltage into  
a current at the IIN pin (virtually ground). The current seen at this pin  
Voltage-controlled output current  
source to 200mA per channel,  
requiring one external set resistor  
per channel  
Current-controlled output current  
source to 200mA per channel  
Rise time = 0.8ns  
Fall time = 0.8ns  
is then amplified to become a current source at pin IOUT  
.
On chip oscillator with frequency  
and amplitude control by use of  
external resistors to ground  
Oscillator to 500MHz  
Oscillator to 100mA pk/pk  
Single +5V supply (±10%)  
An on-chip 500MHz oscillator is provided to allow output current  
modulation when in any mode. This is turned on when the OSCEN pin  
is held high. Complete control of amplitude and frequency is set by  
two external resistors connected to ground at pins RFREQ and RAMP  
(see graphs in this data sheet for further explanation).  
Disable feature for power-up  
protection and power savings  
Fast Settling APC Amplifier  
Output current pulses are enabled when an Lsignal is applied to the  
OUTEN pin. No output current flows when OUTEN is H, and addi-  
tional laser diode protection is provided since the OUTEN input will  
float high when open. Complete IOUT shut-off is also achieved by  
holding the ENABLE pin low, which will override all other control  
pins.  
Applications  
CD-RW applications  
Writable optical drives  
Laser diode current switching  
The EL6283C also includes a fast settling APC amplifier designed to  
interface directly with the front end monitor diode and the sample-  
and-hold amplifier for read and write power control. Its 100MHz  
bandwidth and 30ns settling time enable up to 16X CD-RW design.  
Ordering Information  
Part No  
Temp. Range  
Package  
Outline #  
EL6283CU  
0°C to +70°C  
QSOP-16  
MDP0041  
Connection Diagram  
1
2
3
4
5
6
7
8
VOUT  
VREF  
IINR  
PDIN 16  
VCC 15  
IOUT 14  
RFREQ  
IIN2  
GND 13  
RAMP 12  
ENABLE 11  
OSCEN 10  
IIN3  
OUTEN3  
OUTEN2  
9
VCC  
Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these  
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.  
© 2000 Elantec Semiconductor, Inc.  

与EL6283C相关器件

型号 品牌 获取价格 描述 数据表
EL6283CU ELANTEC

获取价格

3-Channel Laser Diode Driver w/Oscillator & APC Amplifier
EL6286C ELANTEC

获取价格

4-Ch Laser Diode Driver + Oscillator
EL6286CU ELANTEC

获取价格

4-Ch Laser Diode Driver + Oscillator
EL6287C ELANTEC

获取价格

4-Ch Laser Diode Driver + Oscillator
EL6287CU ELANTEC

获取价格

4-Ch Laser Diode Driver + Oscillator
EL6288C ELANTEC

获取价格

3-Channel Laser Diode Driver w/Oscillator & APC Amplifier
EL6288CU ELANTEC

获取价格

3-Channel Laser Diode Driver w/Oscillator & APC Amplifier
EL6290C ELANTEC

获取价格

Laser Diode Driver with Waveform Generator
EL6290CJ ELANTEC

获取价格

Laser Diode Driver with Waveform Generator
EL6290CL ELANTEC

获取价格

Laser Diode Driver with Waveform Generator