5秒后页面跳转
EL6288CU PDF预览

EL6288CU

更新时间: 2024-11-17 23:14:47
品牌 Logo 应用领域
ELANTEC 振荡器驱动器二极管激光二极管放大器PC
页数 文件大小 规格书
2页 139K
描述
3-Channel Laser Diode Driver w/Oscillator & APC Amplifier

EL6288CU 数据手册

 浏览型号EL6288CU的Datasheet PDF文件第2页 
EL6288C - Product Brief  
3-Channel Laser Diode Driver w/Oscillator & APC Amplifier  
Features  
General Description  
• Shrink-Small Package Outline  
The EL6288C is a high-performance three channel laser driver that  
provides controlled current to a grounded laser diode. Channels 2 and  
3 should be used as the write channels, with switching speeds of  
approximately one nanosecond rise/fall time. All three channels are  
summed together at the IOUT output, allowing the user to create multi-  
level waveforms in order to optimize laser diode performance. The  
level of the output current is set by an analog voltage applied to an  
external resistor which converts the voltage into a current at the IIN pin  
(virtually ground). The current seen at this pin is then amplified to  
• Voltage-controlled output current  
source, requiring one external set  
resistor per channel  
• Current-controlled output current  
source  
• Rise time = 0.8ns  
• Fall time = 0.8ns  
• On chip oscillator with frequency  
and amplitude control by use of  
external resistors to ground  
• Oscillator to 500MHz  
• Oscillator to 100mA pk/pk  
• Single +5V supply (±10%)  
• Disable feature for power-up  
protection and power savings  
• Fast Settling APC Amplifier  
become a current source at pin IOUT  
.
An on-chip 500MHz oscillator is provided to allow output current  
modulation when in any mode. This is turned on when the OSCEN pin  
is held high. Complete control of amplitude and frequency is set by  
two external resistors connected to ground at pins RFREQ and RAMP  
(see graphs in this data sheet for further explanation).  
Output current pulses are enabled when an ‘L’ signal is applied to the  
OUTEN pin. No output current flows when OUTEN is ‘H’, and addi-  
tional laser diode protection is provided since the OUTEN input will  
float high when open. Complete IOUT shut-off is also achieved by  
holding the ENABLE pin low, which will override all other control  
pins.  
Applications  
• CD-RW applications  
• Writable optical drives  
• Laser diode current switching  
The EL6288C also includes a fast settling APC amplifier designed to  
interface directly with the front end monitor diode and the sample-  
and-hold amplifier for read and write power control. Its 100MHz  
bandwidth and 30ns settling time enable up to 16X CD-RW design.  
Ordering Information  
Part No  
Temp. Range  
Package  
Outline #  
EL6288CU  
0°C to +70°C  
QSOP-16  
MDP0041  
Connection Diagram  
1
2
3
4
5
6
7
8
VOUT  
VREF  
IINR  
PDIN 16  
VCC 15  
IOUT 14  
IIN2  
GND 13  
IIN3  
RAMP 12  
ENABLE 11  
OSCEN 10  
RFREQ  
OUTEN3  
OUTEN2  
9
VCC  
Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these  
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.  
© 2001 Elantec Semiconductor, Inc.  

与EL6288CU相关器件

型号 品牌 获取价格 描述 数据表
EL6290C ELANTEC

获取价格

Laser Diode Driver with Waveform Generator
EL6290CJ ELANTEC

获取价格

Laser Diode Driver with Waveform Generator
EL6290CL ELANTEC

获取价格

Laser Diode Driver with Waveform Generator
EL6290CL RENESAS

获取价格

EL6290CL
EL6290CU RENESAS

获取价格

EL6290CU
EL6290CU ELANTEC

获取价格

Laser Diode Driver with Waveform Generator
EL6291C ELANTEC

获取价格

Laser Diode Driver with Waveform Generator
EL6291CL ELANTEC

获取价格

Laser Diode Driver with Waveform Generator
EL6291CY ELANTEC

获取价格

Laser Diode Driver with Waveform Generator
EL6293 INTERSIL

获取价格

Laser Diode Driver with Waveform Generator