5秒后页面跳转
EL6286C PDF预览

EL6286C

更新时间: 2024-11-17 23:14:47
品牌 Logo 应用领域
ELANTEC 振荡器驱动器二极管激光二极管
页数 文件大小 规格书
2页 155K
描述
4-Ch Laser Diode Driver + Oscillator

EL6286C 数据手册

 浏览型号EL6286C的Datasheet PDF文件第2页 
EL6286C - Product Brief  
4-Ch Laser Diode Driver + Oscillator  
Features  
General Description  
• “Shrink-Small” Outline Package  
The EL6286C is a four channel laser diode current amplifier that pro-  
vides controlled current to a grounded laser diode. Channels 2, 3, and  
4 must be used as the write channels, with switching speeds of approx-  
imately one nanosecond rise/fall time. All four channels are summed  
together at the IOUT output, allowing the user to create multilevel  
waveforms in order to optimize laser diode performance. The level of  
the output current is set by an analog voltage applied to an external  
resistor which converts the voltage into a current at the IIN pin (virtu-  
ally ground). The current seen at this pin is then amplified to become a  
• Voltage-controlled output current  
source requiring one external set  
resistor per channel  
• Current-controlled output current  
source  
• Rise time = 0.8ns  
• Fall time = 0.8ns  
• On chip oscillator with frequency  
and amplitude control by use of  
external resistors to ground  
• Oscillator to 500MHz  
• Oscillator to 100mA pk/pk  
• Single +5V supply (±10%)  
• Disable feature for power-up  
protection and power savings  
• CMOS control signals  
current source at pin IOUT  
.
An on-chip 500MHz oscillator is provided to allow current modula-  
tion when in any mode. This is turned on when the OSCEN pin is held  
high. Complete control of amplitude and frequency is set by two exter-  
nal resistors connected to ground at pins RFREQ and RAMP (see  
graphs in this data sheet for further explanation).  
Output current pulses are enabled when an ‘L’ signal is applied to the  
OUTEN pin. No output current flows when OUTEN is ‘H’, and addi-  
tional laser diode protection is provided since the OUTEN input will  
float high when open. Complete IOUT shutoff is also achieved by hold-  
ing the ENABLE pin low, which will override all other control pins.  
Applications  
• CD-RW applications  
• Writable optical drives  
• Laser diode current switching  
The external resistors allow the user to accurately and independently  
set each amplifier transconductance by applying a voltage to each  
resistor, without restriction on the voltage range, thus ensuring broad  
voltage DAC compatibility. Alternatively, the IIN pin can be biased  
from a current DAC or other current source.  
Ordering Information  
Part No  
Temp. Range  
Package  
Outline #  
EL6286CU  
0°C to +70°C  
QSOP-24  
MDP0040  
Connection Diagram  
GND  
1
2
3
4
5
6
7
8
9
24 GND  
23 VCC  
IINR  
GND  
22 VCC  
IIN2  
21 IOUT  
20 IOUT  
19 GND  
18 RAMP  
17 ENABLE  
16 OSCEN  
15 VCC  
RFREQ  
IIN3  
IIN4  
OUTENR  
OUTEN2  
OUTEN3 10  
OUTEN4 11  
GND 12  
14 VCC  
13 GND  
Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these  
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.  
© 2001 Elantec Semiconductor, Inc.  

与EL6286C相关器件

型号 品牌 获取价格 描述 数据表
EL6286CU ELANTEC

获取价格

4-Ch Laser Diode Driver + Oscillator
EL6287C ELANTEC

获取价格

4-Ch Laser Diode Driver + Oscillator
EL6287CU ELANTEC

获取价格

4-Ch Laser Diode Driver + Oscillator
EL6288C ELANTEC

获取价格

3-Channel Laser Diode Driver w/Oscillator & APC Amplifier
EL6288CU ELANTEC

获取价格

3-Channel Laser Diode Driver w/Oscillator & APC Amplifier
EL6290C ELANTEC

获取价格

Laser Diode Driver with Waveform Generator
EL6290CJ ELANTEC

获取价格

Laser Diode Driver with Waveform Generator
EL6290CL ELANTEC

获取价格

Laser Diode Driver with Waveform Generator
EL6290CL RENESAS

获取价格

EL6290CL
EL6290CU RENESAS

获取价格

EL6290CU