�ꢀꢁꢂꢃꢁꢄꢅꢆꢇꢈꢉꢅꢄꢈꢊꢆꢋꢈꢌꢍꢎꢏꢐꢌꢍꢎꢑꢈꢌꢆꢒ�ꢋꢈꢍꢆꢆꢓꢄ�ꢋꢓꢈ
�ꢀꢁꢂ
�
ꢀ
ꢁ
ꢂ
ꢃ
ꢄ
ꢅ
ꢁ
ꢆ
ꢇ
ꢃ
ꢈ
ꢃ
ꢉ
ꢊ
�ꢀꢀꢁꢂꢃꢃꢄꢄꢄꢅꢆꢁꢇꢈꢉꢊꢋꢌꢍꢀꢇꢋ�ꢅꢋꢍꢉꢎꢎꢎꢏꢐꢑꢑꢒꢎꢓꢔꢕꢖꢆꢁꢇꢈꢎꢎꢎꢏꢐꢑꢑꢒꢎꢓꢔꢕꢖꢗꢘꢙꢚ
INTRODUCTION
ꢚꢙ
Thiseasy-to-usekitprovidesaplatformfortheevalua-
tionofthePB50andPB58 highvoltagepowerboosters.
The PB50 and PB58 are designed most commonly in
combination with a small signal, general purpose op
amp. However, they can also be used without a driver
amplifier. This kit can be used to analyze a multitude of
standard or proprietary circuit configurations.
ꢈꢉꢊ
ꢈꢉꢊ
ꢈꢉꢊ
ꢈꢉꢊ
ꢆꢀꢔꢔ
ꢆꢀꢔꢔ
PARTS LIST
Part #
Description
Quantity
HS13
Heatsink
1
EVAL01
MS03
HWRE02
HWRE05
TW0 3
PC Board
1
1
1
1
Mating Socket
Hardware Kit
8-Pin Wire Wrap Socket
Thermal Washer
ꢓꢀꢕ
ꢓꢀꢕ
ꢆꢀꢕ
ꢆꢀꢕ
1 Box/10
ꢗꢙ
HWRE02 contains the following:
4
4
4
2
2
#8 x .375" Panhead Screws
#8 x .375" Hex Spacers
#8 x 2.00" Hex Stand Offs
#6 x 1.25" Panhead Screws
#6 x 5/16" Hex Nuts
�ꢘꢑꢖꢃ
�ꢘꢑꢖꢃ
ASSEMBLY
ꢘꢮꢍꢈꢄꢅꢪꢈꢢꢀꢅꢪꢢꢙꢍꢅꢎꢃꢚꢛꢀꢏ
ꢞꢟꢙꢂꢖꢠꢅꢐꢡꢅꢔꢃꢙꢢꢣ
ꢤꢘꢅꢥꢅꢦꢝꢧꢕꢨꢅꢐꢙꢄꢩꢀꢙꢣꢅꢜꢚꢢꢀꢪ
ꢫꢅꢍꢂꢙꢚꢀꢎꢅꢏꢬꢍ
�ꢀꢁꢂꢃꢄꢅ�ꢆꢇꢈꢄꢉ
ꢊꢋꢅꢌꢍꢍꢃꢎꢈꢏꢀꢅꢐꢈꢄꢎ
ꢑꢈꢄꢈꢒꢆꢒꢓ
ꢑꢜꢖꢝꢅꢑꢙꢏꢈꢄꢉꢅꢜꢃꢚꢛꢀꢏ
ꢤꢘꢅꢥꢅꢦꢝꢧꢕꢨ
ꢭꢀꢥꢅꢜꢍꢙꢚꢀꢢꢅ
ꢫꢅꢍꢂꢙꢚꢀꢎꢅꢏꢬꢍ
ꢯꢀꢚꢀꢎꢎꢀꢣꢅꢰꢆꢏꢎ
ꢤꢱꢅꢥꢅꢕꢗꢠꢱꢨ
ꢐꢔꢕꢖꢗꢐꢔꢕꢘ
ꢐꢙꢚꢛꢙꢉꢀ
ꢋꢅꢐꢂꢙꢚꢀꢎ�ꢬꢍ
ꢤꢘꢅꢥꢅꢋꢦꢖꢖꢨ
ꢭꢀꢥꢅꢜꢏꢙꢄꢣꢃꢁꢁ
ꢫꢅꢍꢂꢙꢚꢀꢎꢅꢏꢬꢍ
ꢤꢱꢅꢥꢅꢠꢦꢋꢕꢨ
ꢐꢙꢄꢩꢀꢙꢣꢅꢜꢚꢢꢀꢪꢎ
ꢋꢅꢐꢂꢙꢚꢀꢎꢅ�ꢬꢍ
ꢭꢜꢠꢝꢅꢭꢀꢙꢏꢎꢈꢄꢛ
1. Use thermal grease or Apex Thermal Washer TW03 between power booster and heatsink.
2. Use 18 gauge teflon sleeve on at least two opposite pins
CAUTION
3. Mounting torque greater than 7 in•lbs on power booster mounting bolts will void warranty!
APEX MICROTECHNOLOGY CORPORATION • TELEPHONE (520) 690-8600 • FAX (520) 888-3329 • ORDERS (520) 690-8601 • EMAIL prodlit@apexmicrotech.com
1