Datasheet > 存储 > DRAM> EBE21UE8ACUA-8E-E

EBE21UE8ACUA-8E-E

更新时间： 2024-02-25 07:26:06

品牌	Logo	应用领域
尔必达 - ELPIDA		存储内存集成电路动态存储器双倍数据速率时钟
页数	文件大小	规格书
27页	262K
描述
2GB DDR2 SDRAM SO-DIMM

阅读下载

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

EBE21UE8ACUA-8E-E 技术参数

是否Rohs认证：	符合	生命周期：	Obsolete
零件包装代码：	SODIMM	包装说明：	DIMM, DIMM200,24
针数：	200	Reach Compliance Code：	unknown
ECCN代码：	EAR99	HTS代码：	8542.32.00.36
风险等级：	5.84	Is Samacsys：	N
访问模式：	DUAL BANK PAGE BURST	最长访问时间：	0.4 ns
其他特性：	AUTO/SELF REFRESH	最大时钟频率 (fCLK)：	400 MHz
I/O 类型：	COMMON	JESD-30 代码：	R-XZMA-N200
内存密度：	17179869184 bit	内存集成电路类型：	DDR DRAM MODULE
内存宽度：	64	功能数量：	1
端口数量：	1	端子数量：	200
字数：	268435456 words	字数代码：	256000000
工作模式：	SYNCHRONOUS	最高工作温度：	85 °C
最低工作温度：		组织：	256MX64
输出特性：	3-STATE	封装主体材料：	UNSPECIFIED
封装代码：	DIMM	封装等效代码：	DIMM200,24
封装形状：	RECTANGULAR	封装形式：	MICROELECTRONIC ASSEMBLY
峰值回流温度（摄氏度）：	NOT SPECIFIED	电源：	1.8 V
认证状态：	Not Qualified	刷新周期：	8192
自我刷新：	YES	最大待机电流：	0.16 A
子类别：	DRAMs	最大压摆率：	3.04 mA
最大供电电压 (Vsup)：	1.9 V	最小供电电压 (Vsup)：	1.7 V
标称供电电压 (Vsup)：	1.8 V	表面贴装：	NO
技术：	CMOS	温度等级：	OTHER
端子形式：	NO LEAD	端子节距：	0.6 mm
端子位置：	ZIG-ZAG	处于峰值回流温度下的最长时间：	NOT SPECIFIED
Base Number Matches：	1

EBE21UE8ACUA-8E-E 数据手册

浏览型号EBE21UE8ACUA-8E-E的Datasheet PDF文件第21页

浏览型号EBE21UE8ACUA-8E-E的Datasheet PDF文件第22页

浏览型号EBE21UE8ACUA-8E-E的Datasheet PDF文件第23页

浏览型号EBE21UE8ACUA-8E-E的Datasheet PDF文件第24页

浏览型号EBE21UE8ACUA-8E-E的Datasheet PDF文件第25页

EBE21UE8ACUA

CAUTION FOR HANDLING MEMORY MODULES

When handling or inserting memory modules, be sure not to touch any components on the modules, such as

the memory ICs, chip capacitors and chip resistors. It is necessary to avoid undue mechanical stress on

these components to prevent damaging them.

In particular, do not push module cover or drop the modules in order to protect from mechanical defects,

which would be electrical defects.

When re-packing memory modules, be sure the modules are not touching each other.

Modules in contact with other modules may cause excessive mechanical stress, which may damage the

modules.

MDE0202

NOTES FOR CMOS DEVICES

PRECAUTION AGAINST ESD FOR MOS DEVICES

Exposing the MOS devices to a strong electric field can cause destruction of the gate

oxide and ultimately degrade the MOS devices operation. Steps must be taken to stop

generation of static electricity as much as possible, and quickly dissipate it, when once

it has occurred. Environmental control must be adequate. When it is dry, humidifier

should be used. It is recommended to avoid using insulators that easily build static

electricity. MOS devices must be stored and transported in an anti-static container,

static shielding bag or conductive material. All test and measurement tools including

work bench and floor should be grounded. The operator should be grounded using

wrist strap. MOS devices must not be touched with bare hands. Similar precautions

need to be taken for PW boards with semiconductor MOS devices on it.

HANDLING OF UNUSED INPUT PINS FOR CMOS DEVICES

No connection for CMOS devices input pins can be a cause of malfunction. If no

connection is provided to the input pins, it is possible that an internal input level may be

generated due to noise, etc., hence causing malfunction. CMOS devices behave

differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed

high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected

to V^DDor GND with a resistor, if it is considered to have a possibility of being an output

pin. The unused pins must be handled in accordance with the related specifications.

STATUS BEFORE INITIALIZATION OF MOS DEVICES

Power-on does not necessarily define initial status of MOS devices. Production process

of MOS does not define the initial operation status of the device. Immediately after the

power source is turned ON, the MOS devices with reset function have not yet been

initialized. Hence, power-on does not guarantee output pin levels, I/O settings or

contents of registers. MOS devices are not initialized until the reset signal is received.

Reset operation must be executed immediately after power-on for MOS devices having

reset function.

CME0107

Data Sheet E1217E10 (Ver. 1.0)

1...23 24 252627

下载PDF

与EBE21UE8ACUA-8E-E相关器件

型号	品牌	描述	获取价格	数据表
EBE21UE8ACUA-8G-E	ELPIDA	2GB DDR2 SDRAM SO-DIMM	获取价格
EBE21UE8ACWA	ELPIDA	2GB Unbuffered DDR2 SDRAM DIMM	获取价格
EBE21UE8ACWA-6E-E	ELPIDA	2GB Unbuffered DDR2 SDRAM DIMM	获取价格
EBE21UE8ACWA-8E-E	ELPIDA	2GB Unbuffered DDR2 SDRAM DIMM	获取价格
EBE21UE8ACWA-8G-E	ELPIDA	2GB Unbuffered DDR2 SDRAM DIMM	获取价格
EBE21UE8ACWB	ELPIDA	2GB Unbuffered DDR2 SDRAM DIMM	获取价格

与EBE21UE8ACUA-8E-E相关文章

资料手册解读：UC3842参数和管脚说明
2024-05-22

3
一文带你了解无源晶振的负载电容为何要加两颗谐振电容CL1和CL2
2024-05-22

4
玻璃管保险丝与陶瓷管保险丝：区别与替代性探讨
2024-05-22

3
PCF8574资料解读：主要参数分析、引脚说明
2024-05-21

15

产品中心

服务支持

精选活动

关于我们

帮助中心

EBE21UE8ACUA-8E-E

EBE21UE8ACUA-8E-E 技术参数

EBE21UE8ACUA-8E-E 数据手册

与EBE21UE8ACUA-8E-E相关器件

与EBE21UE8ACUA-8E-E相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

EBE21UE8ACUA-8E-E

EBE21UE8ACUA-8E-E 技术参数

EBE21UE8ACUA-8E-E 数据手册

与EBE21UE8ACUA-8E-E相关器件

与EBE21UE8ACUA-8E-E相关文章

您还可以找

您在本页遇到什么问题？