5秒后页面跳转
DS1624S+T&R PDF预览

DS1624S+T&R

更新时间: 2024-10-28 11:56:11
品牌 Logo 应用领域
美信 - MAXIM 存储
页数 文件大小 规格书
20页 667K
描述
Digital Thermometer and Memory

DS1624S+T&R 数据手册

 浏览型号DS1624S+T&R的Datasheet PDF文件第5页浏览型号DS1624S+T&R的Datasheet PDF文件第6页浏览型号DS1624S+T&R的Datasheet PDF文件第7页浏览型号DS1624S+T&R的Datasheet PDF文件第9页浏览型号DS1624S+T&R的Datasheet PDF文件第10页浏览型号DS1624S+T&R的Datasheet PDF文件第11页 
DS1624  
Temperature is represented in the DS1624 in terms of a 0.03125°C LSB, yielding the following 13–bit  
format:  
MSB  
LSB  
0
0
0
0
1
1
0
0
1
0
0
0
1
0
0
0
= +25.0625°C  
OPERATION AND CONTROL  
A configuration/status register is used to determine the method of operation of the DS1624 will use in a  
particular application as well as indicating the status of the temperature conversion operation.  
The configuration register is defined as follows:  
CONFIGURATION/STATUS REGISTER  
DONE  
1
0
0
1
0
1
1SHOT  
where  
DONE = Conversion Done bit. “1” = Conversion complete, “0” = conversion in progress.  
1SHOT = One Shot Mode. If 1SHOT is “1”, the DS1624 will perform one temperature conversion upon  
receipt of the Start Convert T protocol. If 1SHOT is “0”, the DS1624 will continuously perform  
temperature conversions. This bit is nonvolatile and the DS1624 is shipped with 1SHOT = “0”.  
Since the configuration register is implemented in E2, writes to the register require 10 ms to complete.  
After issuing a command to write to the configuration register, no further accesses to the DS1624 should  
be made for at least 10 ms.  
OPERATION – MEMORY  
BYTE PROGRAM MODE  
In this mode, the master sends addresses and one data byte to the DS1624.  
Following a START condition, the device code (4–bit), the slave address (3 bit), and the R/  
W
bit, which  
is logic LOW, are placed onto the bus by the master. The master then sends the Access Memory protocol.  
This indicates to the addressed DS1624 that a byte with a word address will follow after it has generated  
an acknowledge bit. Therefore, the next byte transmitted by the master is the word address and will be  
written into the address pointer of the DS1624. After receiving the acknowledge of the DS1624, the  
master device transmits the data word to be written into the addressed memory location. The DS1624  
acknowledges again and the master generates a STOP condition. This initiates the internal programming  
cycle of the DS1624. A repeated START condition, instead of a STOP condition, will abort the  
programming operation.  
During the programming cycle the DS1624 will not acknowledge any further accesses to the device until  
the programming cycle is complete (approximately 10 ms.)  
8 of 20  

与DS1624S+T&R相关器件

型号 品牌 获取价格 描述 数据表
DS1625S MAXIM

获取价格

Temperature Sensor, Rectangular, 8 Pin, Surface Mount,
DS1626 DALLAS

获取价格

High-Precision 3-Wire Digital Thermometer and Thermostat
DS1626 ADI

获取价格

高精度、3线数字温度计及温度监控器
DS1626_07 DALLAS

获取价格

High-Precision 3-Wire Digital Thermometer and Thermostat
DS1626S MAXIM

获取价格

Serial Switch/Digital Sensor, 12 Bit(s), 0.50Cel, Rectangular, Surface Mount, SOIC-8
DS1626S+ MAXIM

获取价格

Serial Switch/Digital Sensor, 12 Bit(s), 0.50Cel, Rectangular, Surface Mount, LEAD FREE, S
DS1626S+T&R MAXIM

获取价格

Serial Switch/Digital Sensor, 12 Bit(s), 0.50Cel, Rectangular, Surface Mount, LEAD FREE, S
DS1626U DALLAS

获取价格

High-Precision 3-Wire Digital Thermometer and Thermostat
DS1626U MAXIM

获取价格

Serial Switch/Digital Sensor, 12 Bit(s), 0.50Cel, Rectangular, 8 Pin, Surface Mount, MICRO
DS1626U/T&R MAXIM

获取价格

Serial Switch/Digital Sensor, 12 Bit(s), 0.50Cel, Rectangular, 8 Pin, Surface Mount, MICRO