Datasheet > AD8361_1

AD8361_1

更新时间： 2022-10-09 09:19:58

品牌	Logo	应用领域
亚德诺 - ADI		/
页数	文件大小	规格书
24页	853K
描述
LF to 2.5 GHz TruPwr? Detector

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

AD8361_1 数据手册

AD8361

EVALUATION BOARD

Figure 65 and Figure 68 show the schematic of the AD8361

evaluation board. Note that uninstalled components are drawn

in as dashed. The layout and silkscreen of the component side

are shown in Figure 66, Figure 67, Figure 69, and Figure 70. The

board is powered by a single supply in the 2.7 V to 5.5 V range.

The power supply is decoupled by 100 pF and 0.01 µF

capacitors. Additional decoupling, in the form of a series

resistor or inductor in R6, can also be added. Table 8 details the

various configuration options of the evaluation board.

Table 8. Evaluation Board Configuration Options

Component Function

Default Condition

Not Applicable

TP1, TP2

SW1

Ground and Supply Vector Pins.

Device Enable. When in Position A, the PWDN pin is connected to +V_Sand the AD8361 is in power- SW1 = B

down mode. In Position B, the PWDN pin is grounded, putting the device in operating mode.

SW2/SW3

C1, R2

Operating Mode. Selects either ground reference mode, internal reference mode or supply

reference mode. See Table 4 for more details.

Input Coupling. The 75 Ω resistor in Position R2 combines with the AD8361’s internal input

SW2 = A, SW3 = B

(Ground Reference Mode)

R2 = 75 Ω (Size 0402)

impedance to give a broadband input impedance of around 50 Ω. For more precise matching C1 = 100 pF (Size 0402)

at a particular frequency, R2 can be replaced by a different value (see Input Coupling and

Matching and Figure 43 through Figure 46).

Capacitor C1 ac couples the input signal and creates a high-pass input filter whose corner

frequency is equal to approximately 8 MHz. C1 can be increased for operation at lower

frequencies. If resistive attenuation is desired at the input, series resistor R1, which is

nominally 0 Ω, can be replaced by an appropriate value.

C2, C3, R6

Power Supply Decoupling. The nominal supply decoupling of 0.01 µF and 100 pF. A series

inductor or small resistor can be placed in R6 for additional decoupling.

C2 = 0.01 µF (Size 0402)

C3 = 100 pF (Size 0402)

R6 = 0 Ω (Size 0402)

Filter Capacitor. The internal 50 pF averaging capacitor can be augmented by placing a

capacitance in C5.

C5 = 1 nF (Size 0603)

C4, R5

Output Loading. Resistors and capacitors can be placed in C4 and R5 to load test V rms.

C4 = R5 = Open (Size 0603)

Rev. C | Page 21 of 24

1...18 19 202122 23 24

中文翻译

下载PDF

与AD8361_1相关器件

型号	品牌	获取价格	描述	数据表
AD8361_15	ADI	获取价格	LF to 2.5 GHz TruPwr Detector
AD8361ARM	ADI	获取价格	LF to 2.5 GHz TruPwr⑩ Detector
AD8361ARM-REEL	ADI	获取价格	LF to 2.5 GHz TruPwr⑩ Detector
AD8361ARM-REEL7	ADI	获取价格	LF to 2.5 GHz TruPwr⑩ Detector
AD8361ARMZ	ADI	获取价格	LF to 2.5 GHz TruPwr Detector
AD8361ARMZ1	ADI	获取价格	LF to 2.5 GHz TruPwr? Detector
AD8361ARMZ-REEL	ADI	获取价格	LF to 2.5 GHz TruPwr? Detector
AD8361ARMZ-REEL7	ADI	获取价格	LF to 2.5 GHz TruPwr? Detector
AD8361ART	ADI	获取价格	LF to 2.5 GHz TruPwr Detector
AD8361ART-EVAL	ADI	获取价格	LF to 2.5 GHz TruPwr⑩ Detector