4-Channel, 1.5 MSPS, 10-Bit and 12-Bit
Parallel ADCs with a Sequencer
AD7933/AD7934
FUNCTIONAL BLOCK DIAGRAM
FEATURES
V
AGND
Throughput rate: 1.5 MSPS
DD
Specified for VDD of 2.7 V to 5.25 V
Low power
AD7933/AD7934
V
REFIN/
V
REFOUT
2.5V
6 mW maximum at 1.5 MSPS with 3 V supplies
13.5 mW maximum at 1.5 MSPS with 5 V supplies
4 analog input channels with a sequencer
Software configurable analog inputs
4-channel single-ended inputs
VREF
V
V
0
IN
IN
CLKIN
CONVST
BUSY
12-/10-BIT
SAR ADC
AND
I/P
MUX
T/H
CONTROL
3
2-channel fully differential inputs
2-channel pseudo differential inputs
Accurate on-chip 2.5 V reference
0.2ꢀ maximum @ 25°C, 25 ppm/°C maximum (AD7934)
70 dB SINAD at 50 kHz input frequency
No pipeline delays
SEQUENCER
V
PARALLEL INTERFACE/CONTROL REGISTER
DRIVE
High speed parallel interface—word/byte modes
Full shutdown mode: 2 μA maximum
28-lead TSSOP package
DB0 DB11
CS RD WR W/B
DGND
Figure 1.
GENERAL DESCRIPTION
The AD7933/AD7934 are 10-bit and 12-bit, high speed, low
power, successive approximation (SAR) analog-to-digital
converters (ADCs). The parts operate from a single 2.7 V to
5.25 V power supply and feature throughput rates up to 1.5 MSPS.
The parts contain a low noise, wide bandwidth, differential track-
and-hold amplifier that handles input frequencies up to 50 MHz.
These parts use advanced design techniques to achieve very low
power dissipation at high throughput rates. They also feature
flexible power management options. An on-chip control
register allows the user to set up different operating conditions,
including analog input range and configuration, output coding,
power management, and channel sequencing.
PRODUCT HIGHLIGHTS
The AD7933/AD7934 feature four analog input channels with a
channel sequencer that allows a preprogrammed selection of
channels to be sequentially converted. These parts can accept
either single-ended, fully differential, or pseudo differential
analog inputs.
1. High throughput with low power consumption.
2. Four analog inputs with a channel sequencer.
3. Accurate on-chip 2.5 V reference.
4. Single-ended, pseudo differential or fully differential
analog inputs that are software selectable.
5. Single-supply operation with VDRIVE function.
The VDRIVE function allows the parallel interface to connect
directly to 3 V or 5 V processor systems independent of VDD
6. No pipeline delay.
The conversion process and data acquisition are controlled
using standard control inputs that allow for easy interfacing to
microprocessors and DSPs. The input signal is sampled on the
.
CONVST
falling edge of
this point.
, and the conversion is also initiated at
CONVST
7. Accurate control of the sampling instant via a
input and once-off conversion control.
The AD7933/AD7934 has an accurate on-chip 2.5 V reference
that is used as the reference source for the analog-to-digital
conversion. Alternatively, this pin can be overdriven to provide
an external reference.
Table 1. Related Devices
Device
No. of Bits
12/10
12
No. of Channels
Speed
AD7938/AD7939
AD7938-6
8
8
4
1.5 MSPS
625 kSPS
625 kSPS
AD7934-6
12
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 www.analog.com
Fax: 781.461.3113 ©2005–2007 Analog Devices, Inc. All rights reserved.