Surface Mount DIP Switches
SꢀRꢁꢀS 97
Half-Pitch
APPLIꢀAꢁIꢂꢃS
FꢀꢂTURꢀS
Used in any DIP application where
space is at a premium such as
notebook computers, hand-held
radios, industrial control products,
ꢀD-RꢂMdrives,cellularbasestations
and coin changers.
• Half the Size of Standard DIP Switches
• Available in 2, 4, 6, 8, and 10 Positions
• Low Profile
• Less Mass for Easy Vacuum Pick &
Place
Fig. 1 Series 97ꢀ DIMEꢃSIꢂꢃS ꢁn inches (and millimeters)
Top View
Front View
Side View
Recommended PC Pad Dimensions
.050 (1,27) Pitch
LENGTH
SEE ORDERING
INFORMATION
TAPE THICKNESS
.003 (0,08)
.059
(1,50)
.177
(4,50)
.291
(7,39)
.030 (0,76)
.193
(4,90)
.242
(6,15)
.024 (0,61)
.264 (6,71)
.050
(1,27)
Pitch
.016
.004
(0,10)
(0,41)
Unless otherwise specified, tolerances are ±0.008 (0,20)
Fig. 2 Series 97R DIMEꢃSIꢂꢃS ꢁn inches (and millimeters)
Top View
A
Front View
Side View
Recommended PC Pad Dimensions
.047
(1,20)
.057
(1,44)
.177±.002
.050 (1,27) PꢁTCH
TꢂPꢀ
.002
(0,05)
(4,50±0,05)
ON
1
.360
(9,10)
.030
.260
(0,76)
(6,60)
.024
(0,6)
.310
(7,85)
.016
(0,40)
.050
2
3
4
5
6
7
8
(1,27)
.319
(8,1)
PꢁTCH
.024
(0,6)
.004±.004
(0,10±0,10)
Unless otherwise specified, tolerances are ±0.008 (0,20)
Operating Temperature Range: -40 to 85°C
Storage Temperature Range: -40 to 85°C
CꢁRCUꢁTRy
SPECIFICATIONS
Electrical Ratings
Contact Rating: 25 mA at 24 Vdc switching;
100 mA at 50 Vdc non-switching
Materials
Contact Resistance: 100 mΩ max, initially
Insulation Resistance: 100 MΩ minimum
at 100 Vdc
Dielectric Strength: 300 Vac for one minute
Switch Capacitance: 5pF maximum
Contact Arrangement: SPST
Base and Cover: UL94V-0 ꢃylon, black
Actuators: UL94V-0 ꢃylon thermoplastic,
white
avoid flux adhering to the switch body from
the circuit board soldering process.ꢁhe switch
should be allowed to cool for at least 3 minutes
between the end of the solder process and the
beginning of the wash process. ꢁhe solvent
stage of the cleaning process is not to exceed
1 minute and the whole wash process is not to
exceed 3 minutes.Ultrasonic or pressure wash
cleaning is not recommended.
Base Contacts: Alloy copper with gold-plating
over nickel
Terminals: Brass with gold-plating
Tape Seal: Kapton
Mechanical Ratings
Life: 1,000 cycles minimum
Operation Force: 500 gF
Soldering Information
Vapor phase and IR-reflow soldering
can be applied. With stands 255°C peak
temperature.
Mechanical Shock: MIL-SꢁD-202F, Method,
213B, ꢁest ꢀondition A. Gravity: 50G's (peak
value), 11 m/sec. Direction and times: 6 sides
and 3 times in each direction.
Vibration: MIL-SꢁD-202F, Method 201A.
Passed 6 hours (2 hours in each) of three
perpendicular planes at a cycle of 10-55-
10Hz/1 minute.
Packaging Information
Tube:130pcs/tube(2positions),75pcs/tube(4
positions),54pcs/tube(6positions),40pcs/tube
(8 positions), 33 pcs/tube (10 positions).
ꢁape and Reel: 97ꢀ: 4,000 pcs/reel (all
positions). 97R: 2500 pcs/reel (all positions).
Cleaning: ꢁape sealed versions are capable
of withstanding washing processes using
alcohol-based solvents only. Water or other
water-based solvent washing processes are
not recommended. Care should be taken to
Actuation Instructions: Switch slides should
be actuated from a low angle in the intended
direction of travel. ꢁhe application of excess
force from a high angle can cause permanent
damage to the contact system of the switch.
ꢁapesealsmustberemovedtoproperlyactuate
the switches as described above.ꢀlick here for
visual sample.
ORDERING INFORMATION
Series: 97C see fig. 1, 97R see fig. 2
Positions: 02 = .148 (3,76), 04 = .248 (6,30), 06 = .348 (8,84),
08 = .448 (11,38), 10 = .548 (13,92)
97C06SRT
T= RoHS compliant
Packaging: Blank = Tube, R = Tape and Reel (see pkg note)
Seal: Blank = Unsealed, S = Top Tape Seal
All DIP switches are shipped in the "ꢂꢃ"
position.
DIP
4
Grayhill, Inc.
• 561 Hillgrove Avenue • LaGrange, Illinois 60525-5997 • USA • Phone: 708-354-1040 • Fax: 708-354-2820 • www.grayhill.com