1D8W_1.5RP series
1W - Single Output DC-DC Converter - Wide Input - Isolated & Regulated
DC-DC Converter
1 Watt
The 1D8W_1.5RP Series is specially designed for applications where a wide range
input voltage power supplies are isolated from the input power supply in a
distributed power supply system on a circuit board.
Wide input range (2:1)
Ultra compact DIP package
1.5kVDC isolation
Operating temperature range:
-40°C ~ +85°C
International standard pinout
No external component
required
High efficiency up to 80%
RoHS Compliance
These products apply to:
1) Where the voltage of the input power supply is wide range (voltage range ≤2:1);
2) Where isolation is necessary between input and output
(Isolation Voltage ≤1500VDC);
Short circuit protection (SCP)
EN62368, UL62368 approved
3) Where the regulation of the output voltage and the output ripple noise are
demanded.
The ultra-small volume design makes the converters an ideal solution for commu-
nications, instrumentation and industrial electronics applications.
UL-62368-1 (E347551)
Common specifications
Short circuit protection:
Cooling:
Output specifications
Continuous
Item
Test condition
Min
Typ
1
Max
3
Units
%
Free air convection
Voltage accuracy
5%-100% load, input
voltage range
Operation temperature range:
Storage temperature:
-40°C~+85°C
No load output
voltage accuracy
input voltage range
• 3.3VDC output
• others
-55°C~+125°C
5
1.5
7
5
%
%
Storage humidity range:
Pin soldering resistance temperature:
Reflow soldering temperature:
< 95% non-condensing
300°C MAX, 1.5mm away from case for 10s.
Line regulation
Input voltage from low
to high @full load
0.2
0.5
%
Peak temperature ≤245°C, duration
≤60s max. over 217°C. see also IPC/
JEDEC J-STD-020D.1.
Load regulation
5%-100% load
0.5
1
%
Temperature drift
100% full load
0.03
%/°C
ms
Case material:
Black flame-retardant, heat-resistant
plastic
Transient recovery
time
25% load step change
1
3
MTBF (MIL-HDBK-217F@25°C):
Weight:
>1,000,000 hours
2.2g
Transient response
deviation
25% load step change
2.5
100
5
%
Switching frequency Full load, nominal input
KHz
Dimensions:
14.00 × 14.00 × 9.00 mm
Input specifications
EMC specifications
Item
Test condition
Min
Typ
Max
Units
EMI
CE
CISPR32/EN55032
CLASS B (See EMC recommended circuit, ②)
Input current
(full load/no load)
• 12VDC
• 24VDC
111/15 114/30 mA
55/6
57/10
EMI
RE
CISPR32/EN55032
CLASS B (See EMC recommended circuit, ②)
Reflected ripple
current
• 12VDC
• 24VDC
40
55
mA
EMS
EMS
EMS
ESD
RS
IEC/EN61000-4-2
IEC/EN61000-4-3
IEC/EN61000-4-4
Contact 6KV
10V/m
perf. Criteria B
Surge voltage
(1sec. max)
• 12VDC
• 24VDC
-0.7
-0.7
25
50
VDC
VDC
perf. Criteria A
perf. Criteria B
EFT
2KV
Start-up voltage
• 12VDC
• 24VDC
9
18
VDC
VDC
(External Circuit Refer to recommended circuit, ①)
EMS
EMS
Surge
CS
IEC/EN61000-4-5
(External Circuit Refer to recommended circuit, ①)
line to line 2KV
perf. Criteria B
Input Filter
Hot plug
Capacitance filter
unavailable
IEC/EN61000-4-6 3 Vr.m.s perf. Criteria A
Isolation specifications
Item
Example:
1D8W_1205S1.5RP
Test condition
Min
Typ
100
Max
Units
VDC
1 = 1Watt; D8 = DIP8; W = Wide input; 12Vin; 5Vout; S = Single output;
1.5 = 1.5kVDC; R = Regulated output; P = Short circuit protection (SCP)
Isolation voltage
Input-output electric
Strength test for 1 min.
with a leakage current
of 1mA max.
1500
Note:
Isolation resistance
500VDC
1000
MΩ
pF
1. Unless otherwise specified, data in this data sheet should be tested under the
conditions of Ta = 25°C, nominal input voltage and rated output current;
2. The maximum capacitive load offered was tested at input voltage range and
full load;
Isolation capacitance 100KHz/0.1V
3. All index testing methods in this datasheet are based on our Company’s
corporate standards.
4. We can provide product customization service, please contact our technicians
directly for specific information.
Page 1 of 4
1D8W_1.5RP – Rev. 2020-1.2
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com