CURRENTSENSORS
Outgassing Compliant Current Sensors CP-N0530
•ꢀFor use from 50 kHz to nearly 1 MHz
•ꢀTwo different pinouts to meet the requirements of different
applications.
•ꢀLow primary DC resistance
•ꢀ500 Vac isolation from secondary to the core
Core material Ferrite
Terminations Tin-lead (63/37) over tin over nickel over phos bronze
(pins 1 – 6); tin-lead over gold over nickel over copper (pins 7 – 8)
Weight 0.4 g
Ambient temperature –55°C to +125°C
Storage temperature Component: –55°C to +125°C.
Tape and reel packaging: –55°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Packaging 250/7″ reel Plastic tape: 16 mm wide, 0.35 mm thick,
12 mm pocket spacing, 5.6 mm pocket depth
PCB washing Only pure water or alcohol recommended
Sensed
Terminating
Volt-time
product5
(V-µsec)
DCR max (Ohms)
primary secondary
4
Turns (N)
pri:sec
Inductance2
min (µH)
current3 resistance RT
Part number (CP-N0530-)1
Iin (A)
(Ohms)
0201SZ
0301SZ
0401SZ
0501SZ
0601SZ
0202SZ
0302SZ
0402SZ
0502SZ
0602SZ
1:20
1:30
1:40
1:50
1:60
81
180
320
500
730
0.0007
0.0007
0.0007
0.0007
0.0007
0.400
0.870
1.14
10
10
10
10
10
2.0
3.0
4.0
5.0
6.0
16
24
32
41
49
1.50
1.98
0701SZ
1001SZ
1251SZ
0702SZ
1002SZ
1252SZ
1:70
1:100
1:125
980
2000
3000
0.0007
0.0007
0.0007
4.75
5.50
6.50
10
10
10
7.0
10.0
12.5
57
81
101
1. When ordering, please specify the complete part number,
e.g. CP-N0530-0202SZ
2. Inductance measured between secondary pins at 100 kHz, 0.1 Vrms.
3. Primary current of 10 A causes approximately 25°C temperature rise
from 25°C ambient. Higher current causes a greater temperature rise
(see Temperature Rise vs Current curve).
Typical Circuits
CP-N0530-xxx1
8
6
4. Terminating resistance (RT) value is based on 1 Volt output with
10 Amps flowing through the primary. Varying terminating resistance
increases or decreases output Voltage/Ampere according to the fol-
lowing equation: RT (Ohms) = Vout × Nsec/Iin.
Pri
(1 turn)
Sec
(N turns)
I
R
T
Vout
in
5. Maximum volt-time product for the secondary.
6. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
7
4
CP-N0530-xxx2
8
1
Pri
(1 turn)
Sec
(N turns)
I
R
T
Vout
in
7
3
Document CP385-1 Revised 06/28/12
®
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Fax 847-639-1508
1102 Silver Lake Road
Cary, IL 60013
Phone 800-981-0363
Email cps@coilcraft.com Specifications subject to change without notice.
www.coilcraft-cps.com
Please check our web site for latest information.
© Coilcraft, Inc. 2012