Document 1032-1
Shielded Power Inductors
–
XAL1350
• High current and very low DCR
• Soft saturation makes them ideal for VRM/VRD applications.
Core material Composite
Environmental RoHS compliant, halogen free
Terminations RoHS compliant tin-silver over copper. Other terminations
available at additional cost.
Weight 4.5 – 4.9 g
Ambient temperature –40°C to +125°C with (40°C rise) Irms current.
Maximum part temperature +165°C (ambient + temp rise). Derating.
Storage temperature Component: –40°C to +165°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 400/13″ reel Plastic tape: 24 mm wide, 0.3 mm thick,
20 mm pocket spacing, 5.2 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
DCR
Irms (A)6
SRF
typ4
(mOhms)3
typ
Inductance2
(µH)
Percent
Isat5
20°C
rise
40°C
rise
Irms Testing
Irms testing was performed on
0.75 inch wide × 0.25 inch thick
copper traces in still air.
Part number1
tolerance
max
(MHz)
(A)
XAL1350-631_E_
XAL1350-931_E_
XAL1350-132_E_
XAL1350-222_E_
XAL1350-302_E_
0.63
0.93
1.3
2.2
3.0
30,20
30,20
30,20
30,20
30,20
1.50
2.00
2.50
4.16
5.86
1.70
2.20
2.70
4.80
6.80
50
42
33
23
19
74
60
56
46
37
28
25
23
19
16
38
33
32
24
21
Temperature rise is highly
dependent on many factors
including pcb land pattern,
trace size, and proximity to
other components. Therefore
temperature rise should be
verified in application conditions.
1. When ordering, please specify tolerance and packaging codes:
XAL1350-302NED
Tolerance: N = 30%, M = 20% (Table above shows stock tolerances in bold.)
Packaging: D = 13″ machine-ready reel. EIA-481 embossed plastic tape (400 parts per full reel).
B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added
($25 charge), use code letter D instead.
2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using an Agilent/HP 4395A or equivalent.
5. DC current at which the inductance drops 30% (typ) from its value without current.
6. Current that causes the specified temperature rise from 25°C ambient.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
These parts are preproduction products for electrical evaluation only.
Document 1032-1 Revised 07/13/16
US +1-847-639-6400 sales@coilcraft.com
Specification subject to change without notice.
UK +44-1236-730595 sales@coilcraft-europe.com
© Coilcraft Inc. 2016
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.
Taiwan +886-2-2264 3646 sales@coilcraft.com.tw
China +86-21-6218 8074 sales@coilcraft.com.cn
Singapore + 65-6484 8412 sales@coilcraft.com.sg