UPC2781GR
SI MMIC IQ DEMODULATOR
INTERNAL BLOCK DIAGRAM
FEATURES
• RF BANDWIDTH:
440 - 520 MHz
•
IF BANDWIDTH:
0.3 - 20 MHz
GND(IQ)
20
19
18
I OUT
I OUT
1
2
•
•
ON CHIP 90˚ PHASE SHIFTER
VCC(IF-I)
IQ PHASE AND AMPLITUDE BALANCE
Amplitude Balance: ± 0.5 dB
Phase Balance: ± 2.0 degree
V
AGC
3
4
OSC OUT
GND(RF)
RF IN
•
LOW IM3 DISTORTION:
35 dBc Typical
17 OSC-B2
16
15
14
90 deg
phase
shifter
OSC-C1
OSC-C2
OSC-B1
GND(PS)
5
6
•
•
SMALL 20 PIN SSOP PACKAGE
TAPE AND REEL PACKAGE AVAILABLE
RF IN
AGC
AMP.
DESCRIPTION
GND(IQ)
7
8
9
The UPC2781GR is a Silicon MMIC IQ demodulator manu-
factured with the NESAT III™ silicon bipolar process. The IC
consists of an AGC amplifier, double balanced mixers, oscil-
lator, 90˚ phase shifter, and I&Q output buffer amps. The
device was specifically designed for DBS receivers and other
digital communication systems.
VCC(RF)
13
V
CC(IF-Q)
12 Q OUT
V
CC(PS) 10
11
Q OUT
NEC's stringent quality assurance and test procedures en-
sure the highest reliability and performance.
ELECTRICAL CHARACTERISTICS (TA = 25°C, VCC = 5 V, ZL = 1k Ω)
PART NUMBER
UPC2781GR
PACKAGE OUTLINE
S20 (SSOP 20)
SYMBOLS
PARAMETERS AND CONDITIONS
Supply Current (no input signal)
UNITS
MIN
52
TYP
70
MAX
88
ICC
fRF
fIF
mA
RF Input Bandwidth (fIF = 10 MHz, fRF > fLO, IQ Phase Balance < ± 1.5˚)
MHz
MHz
440
0.3
480
520
20
IF Output Bandwidth
(fRF = 480 MHz, PLO = -10 dBm, fRF > fLO, VAGC = 0 V)
CG
NF
IM3
Conversion Gain (fRF = 480 MHZ, fIF = 10 MHZ, VAGC = 0 V)
dB
dB
50
18
Noise Figure (fRF = 480 MHZ, fIF = 10 MHZ, PLO = -10 dBm, VAGC = 0 V)
3rd Order Intermodulation Distortion
(fRF1 = 480 MHz, fRF2 = 481 MHz, fLO = 470 MHz, PLO = -10 dBm)
dBc
deg
35
∆Φ
∆G
IQ Phase Balance
(fRF = 480 MHZ, fIF = 10 MHZ, PRF = -30 dBm, PLO = -10 dBm)
-2
-0.5
15
+2
IQ Amplitude Balance
(fRF = 480 MHz, fIF = 10 MHZ, PRF = -30 dBm, PLO = -10 dBm, VAGC = 0 V)
dB
dB
dB
dB
+0.5
GAGC
LO-RF
LO-IF
AGC Control Range
(fRF = 480MHZ, PRF = -30dBm, fIF = 10MHZ, PLO = -10dBm, 0 ≤ VAGC ≤ 5 V)
20
30
20
LO to RF Isolation
(fLO = 470 MHZ, PLO = -10 dBm, PRF = -30 dBm, VAGC = 0 V)
LO to IF Isolation
(fLO = 470 MHZ, PLO = -10 dBm, PRF = -30 dBm, VAGC = 0 V)
PO (SAT)
VO
Maximum Output Power (fRF = 480 MHz, fIF = 10 MHZ, PRF = -10 dBm)
dBm
0
Output Voltage (fRF = 480 MHZ, fIF = 10 MHZ, PLO = -10 dBm, ZL = 1k Ω)
VP-P
1.0
California Eastern Laboratories