TMUX7308F, TMUX7309F
SCDS403B – FEBRUARY 2021 – REVISED DECEMBER 2021
TMUX730xF ±60-V Fault-Protected, 8:1 and Dual 4:1 Multiplexers with Latch-Up
Immunity and 1.8-V Logic
1 Features
3 Description
•
Wide supply range:
The TMUX7308F and TMUX7309F are modern
complementary metal-oxide semiconductor (CMOS)
analog multiplexers in 8:1 (single ended) and 4:1
(differential) configurations. The devices work well
with dual supplies (±5 V to ±22 V), a single supply (8
V to 44 V), or asymmetric supplies (such as VDD = 12
V, VSS = –5 V). The overvoltage protection is available
in powered and powered-off conditions, making the
TMUX7308F and TMUX7309F devices suitable for
applications where power supply sequencing cannot
be precisely controlled.
– Dual supply: ±5 V to ±22 V
– Single supply: 8 V to 44 V
Integrated fault protection:
– Overvoltage protection, source to supplies or
source to drain: ±85 V
– Overvoltage protection: ±60 V
– Powered-off protection: ±60 V
– Non-fault channels continue to operate
– Known state without logic inputs present
– Output clamped to the supply in overvoltage
condition
•
The device blocks fault voltage up to +60 V or –60
V relative to ground in both powered and powered-off
conditions. When no power supplies are present, the
switch channels remain in the OFF state regardless of
switch input conditions and logic control status. Under
normal operation conditions, if the analog input signal
level on any Sx pin exceeds the supply voltage (VDD
or VSS) by a threshold voltage (VT), the channel turns
OFF and the Sx pin becomes high impedance. When
the fault channel is selected, the drain pin (D or Dx) is
pulled to the supply (VDD or VSS) that was exceeded.
•
•
•
•
•
•
Latch-up immune
1.8-V Logic capable
Fail-safe logic: up to 44 V independent of supply
Integrated pull-down resistor on logic pins
Break-before-make switching
Industry standard TSSOP and
smaller WQFN packages
2 Applications
•
•
•
•
•
•
•
Factory automation and control
Programmable logic controllers (PLC)
Analog input modules
Semiconductor test equipment
Battery test equipment
The low capacitance, low charge injection, and
integrated fault protection enables the TMUX7308F
and TMUX7309F devices to be used in front end
data acquisition applications where high performance
and high robustness are both critical. The devices are
available in a standard TSSOP package and smaller
WQFN package (ideal if PCB space is limited).
Servo drive control module
Data acquisition systems (DAQ)
VDD
VSS
VDD
VSS
SW
SW
SW
Device Information(1)
S1
S2
S1A
DA
DB
PART NUMBER
PACKAGE
TSSOP (16)(2)
WQFN (16)
BODY SIZE (NOM)
5.00 mm × 4.40 mm
4.00 mm × 4.00 mm
SW
SW
S4A
S1B
TMUX7308F
TMUX7309F
D
SW
SW
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
S4B
S8
(2) Preview package for TMUX7309F.
A0
A1
A2
EN
A0
A1
EN
Fault Detection/
Switch Driver/
Logic Decoder
Fault Detection/
Switch Driver/
Logic Decoder
TMUX7308F
TMUX7309F
Functional Block Diagram
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.