TMS29F400T, TMS29F400B
524288 BY 8-BIT/262144 BY 16-BIT
FLASH MEMORIES
SMJS843A – MAY 1997 – REVISED SEPTEMBER 1997
Single Power Supply Supports 5 V 10%
Read/Write Operation
Erase Suspend/Resume
– Supports Reading Data From, or
Programming Data to, a Sector Not
Being Erased
Organization . . . 524288 By 8 Bits
262144 By 16 Bits
Hardware-Reset Pin Initializes the
Internal-State Machine to the Read
Operation
Array-Blocking Architecture
– One 16K-Byte/One 8K-Word Boot Sector
– Two 8K-Byte/4K-Word Parameter Sectors
– One 32K-Byte/16K-Word Sector
– Seven 64K-Byte/32K-Word Sectors
– Any Combination of Sectors Can Be
Erased. Supports Full-Chip Erase
– Any Combination of Sectors Can Be
Marked as Read-Only
Package Options
– 44-Pin Plastic Small-Outline Package
(PSOP) (DBJ Suffix)
– 48-Pin Thin Small-Outline Package
(TSOP) (DCD Suffix)
Detection Of Program/Erase Operation
– Data Polling and Toggle Bit Feature of
Program/Erase Cycle Completion
Boot-Code Sector Architecture
– T = Top Sector
– B = Bottom Sector
– Hardware Method for Detection of
Program/Erase Cycle Completion
Sector Protection
Through Ready/Busy (RY/BY) Output Pin
– Hardware Protection Method That
Disables Any Combination of Sectors
From Write or Erase Operations Using
Standard Programming Equipment
High-Speed Data Access at 5-V V
at Three Temperature Ranges
10%
CC
– 80 ns
– 90 ns
– 100 ns
– 120 ns
Commercial . . . 0°C to 70°C
Commercial . . . 0°C to 70°C
Extended . . . –40°C to 85°C
Automotive . . . –40°C to 125°C
Embedded Program/Erase Algorithms
– Automatically Pre-Programs and Erases
Any Sector
– Automatically Programs and Verifies the
Program Data at Specified Address
JEDEC Standards
PIN NOMENCLATURE
– Compatible With JEDEC Byte Pinouts
– Compatible With JEDEC EEPROM
Command Set
A[0:17]
BYTE
Address Inputs
Byte/Word Enable
Data In/Data out
DQ[0:14]
Fully Automated On-Chip Erase and
Program Operations
DQ15/A
Data In/Out (Word-Wide Mode)
Low-Order Address (Byte-Wide Mode)
Chip Enable
–1
100 000 Program/Erase Cycles
CE
OE
Output Enable
Low Power Dissipation
NC
No Internal Connection
Reset/Deep Power Down
Ready/Busy Output
Power Supply
– 40-mA Typical Active Read for Byte Mode
– 50-mA Typical Active Read for Word
Mode
– 60-mA Typical Program/Erase Current
– Less Than 100-µA Standby Current
– 5 µA in Deep Power-Down Mode
RESET
RY/BY
V
V
CC
Ground
SS
WE
Write Enable
All Inputs/Outputs TTL-Compatible
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 1997, Texas Instruments Incorporated
PRODUCT PREVIEW information concerns products in the formative or
design phase of development. Characteristic data and other
specifications are design goals. Texas Instruments reserves the right to
change or discontinue these products without notice.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443