256 Kbit / 512 Kbit / 1 Mbit / 2 Mbit (x8)
Many-Time Programmable Flash
SST27SF256 / SST27SF512 / SST27SF010 / SST27SF020
SST27SF256 / 512 / 010 / 0205.0V-Read 256Kb / 512Kb / 1Mb / 2Mb (x8) MTP flash memories
Data Sheet
FEATURES:
•
•
•
Organized as 32K x8 / 64K x8 / 128K x8 / 256K x8
4.5-5.5V Read Operation
•
Fast Byte-Program Operation
– Byte-Program Time: 20 µs (typical)
– Chip Program Time:
Superior Reliability
0.7 seconds (typical) for SST27SF256
1.4 seconds (typical) for SST27SF512
2.8 seconds (typical) for SST27SF010
5.6 seconds (typical) for SST27SF020
– Endurance: At least 1000 Cycles
– Greater than 100 years Data Retention
•
•
Low Power Consumption
– Active Current: 20 mA (typical)
– Standby Current: 10 µA (typical)
•
Electrical Erase Using Programmer
– Does not require UV source
– Chip-Erase Time: 100 ms (typical)
Fast Read Access Time
– 70 ns
– 90 ns
•
•
•
TTL I/O Compatibility
JEDEC Standard Byte-wide EPROM Pinouts
Packages Available
– 32-pin PLCC
– 32-pin TSOP (8mm x 14mm)
– 28-pin PDIP for SST27SF256/512
– 32-pin PDIP for SST27SF010/020
PRODUCT DESCRIPTION
The SST27SF256/512/010/020 are a 32K x8 / 64K x8 /
128K x8 / 256K x8 CMOS, Many-Time Programmable
(MTP) low cost flash, manufactured with SST’s proprietary,
high performance SuperFlash technology. The split-gate
cell design and thick oxide tunneling injector attain better
reliability and manufacturability compared with alternate
approaches. These MTP devices can be electrically erased
and programmed at least 1000 times using an external pro-
grammer with a 12 volt power supply. They have to be
erased prior to programming. These devices conform to
JEDEC standard pinouts for byte-wide memories.
Device Operation
The SST27SF256/512/010/020 are a low cost flash solu-
tion that can be used to replace existing UV-EPROM, OTP,
and mask ROM sockets. These devices are functionally
(read and program) and pin compatible with industry stan-
dard EPROM products. In addition to EPROM functionality,
these devices also support electrical erase operation via an
external programmer. They do not require a UV source to
erase, and therefore the packages do not have a window.
Read
Featuring high performance Byte-Program, the
SST27SF256/512/010/020 provide a Byte-Program time of
20 µs. Designed, manufactured, and tested for a wide
spectrum of applications, these devices are offered with an
endurance of at least 1000 cycles. Data retention is rated at
greater than 100 years.
The Read operation of the SST27SF256/512/010/020 is
controlled by CE# and OE#. Both CE# and OE# have to be
low for the system to obtain data from the outputs. Once
the address is stable, the address access time is equal to
the delay from CE# to output (TCE). Data is available at the
output after a delay of TOE from the falling edge of OE#,
assuming that CE# pin has been low and the addresses
have been stable for at least TCE - TOE. When the CE# pin
is high, the chip is deselected and a typical standby current
of 10 µA is consumed. OE# is the output control and is
used to gate data from the output pins. The data bus is in
high impedance state when either CE# or OE# is high.
The SST27SF256/512/010/020 are suited for applications
that require infrequent writes and low power nonvolatile
storage. These devices will improve flexibility, efficiency,
and performance while matching the low cost in nonvolatile
applications that currently use UV-EPROMs, OTPs, and
mask ROMs.
To meet surface mount and conventional through hole
requirements, the SST27SF256/512 are offered in 32-pin
PLCC, 32-pin TSOP, and 28-pin PDIP packages. The
SST27SF010/020 are offered in 32-pin PDIP, 32-pin PLCC
and 32-pin TSOP packages. See Figures 1, 2, and 3 for
pinouts.
Byte-Program Operation
The SST27SF256/512/010/020 are programmed by using
an external programmer. The programming mode for
SST27SF256/010/020 is activated by asserting 12V (±5%)
©2001 Silicon Storage Technology, Inc.
The SST logo and SuperFlash are registered trademarks of Silicon Storage Technology, Inc.
MTP is a trademark of Silicon Storage Technology, Inc.
S71152-02-000 5/01
1
502
These specifications are subject to change without notice.
5秒后页面跳转
STM32H743技术深度剖析与应用案例探索
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
74HC14芯片资料介绍：性能特性分析、引脚介绍
LM1875芯片手册：功放参数分析、引脚说明、电路设计要点
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
