SN74AVC24T245
24-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES552C–FEBRUARY 2004–REVISED AUGUST 2005
FEATURES
•
Control Inputs VIH/VIL Levels Are Referenced
to VCCA Voltage
•
Ioff Supports Partial-Power-Down Mode
Operation
•
VCC Isolation Feature – If Either VCC Input Is at
GND, All Outputs Are in the High-Impedance
State
•
•
I/Os Are 4.6-V Tolerant
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
•
•
Overvoltage-Tolerant Inputs/Outputs Allow
Mixed-Voltage-Mode Data Communications
•
ESD Protection Exceeds JESD 22
– 8000-V Human-Body Model (A114-A)
– 200-V Machine Model (A115-A)
Fully Configurable Dual-Rail Design Allows
Each Port to Operate Over Full 1.2-V to 3.6-V
Power-Supply Range
– 1000-V Charged-Device Model (C101)
DESCRIPTION/ORDERING INFORMATION
This 24-bit noninverting bus transceiver uses two separate configurable power-supply rails. The
SN74AVC24T245 is optimized to operate with VCCA/VCCB set at 1.4 V to 3.6 V. It is operational with VCCA/VCCB as
low as 1.2 V. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.2 V to 3.6 V. The
B port is designed to track VCCB. VCCB accepts any supply voltage from 1.2 V to 3.6 V. This allows for universal
low-voltage bidirectional translation between any of the 1.2-V, 1.5-V, 1.8-V, 2.5-V, and 3.3-V voltage nodes.
The SN74AVC24T245 is designed for asynchronous communication between data buses. The device transmits
data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the
direction-control (DIR) input. The output-enable (OE) input can be used to disable the outputs so the buses are
effectively isolated.
The SN74AVC24T245 is designed so that the control pins (1DIR, 2DIR, 3DIR, 4DIR, 5DIR, 6DIR, 1OE, 2OE,
3OE, 4OE, 5OE, and 6OE) are supplied by VCCA
.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,
preventing damaging current backflow through the device when it is powered down.
The VCC isolation feature ensures that if either VCC input is at GND, then both ports are in the high-impedance
state.
To ensure the high-impedance state during power up or power down, OE should be tied to VCCA through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
ORDERING INFORMATION
TA
PACKAGE(1)
ORDERABLE PART NUMBER
SN74AVC24T245GRGR
TOP-SIDE MARKING
LFBGA – GRG
LFBGA – ZRG (Pb-free)
Tape and reel
Tape and reel
–40°C to 85°C
WH245
SN74AVC24T245ZRGR
(1) Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2004–2005, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.