SCR2-10-10-X-X.XX-XX
REVISION H
DESIGNED & DIMENSIONED
IN MILLIMETERS[INCHES]
SIZE
END OPTION
-10
-D: DOUBLE ENDED
(USE BODY IPD1-05-D)
-BC: BLUNT CUT-
**
POSITIONS
-10
(SEE FIG 2, SHT 2)
-DK: DOUBLE ENDED
KEYED POLARIZATION
PLATING
-S: SELECTIVE GOLD
-F: FLASH SELECTIVE GOLD
LENGTH*
-X.XX (IN METERS),
"A" (SEE TABLE 1)
0.25[9.84] MIN - 1.00[39.37] MAX
(SEE NOTE 3)
*NOTE: -0.25 AND -0.50 ARE CATALOG STANDARD
LENGTHS. FOR OTHER LENGTHS CONTACT SAMTEC.
** -D OPTION, DO NOT DESIGN IN
SAMTEC WILL ONLY SUPPORT EXISTING BUSINESS AS OF REV D
FIG. 1
SCR2-10-10-X-X.XX-DK SHOWN
-DK: DOUBLE-ENDED KEYED POLARIZATION
(SEE FIG.3 TO SEE ASSEMBLY AS SHIPPED)
H
"B" (SEE TABLE 1)
"B" = "A" + 19.16[.754]
(SEE NOTES 3,4, & 6)
C1
H
100±10 3.9±.4
DO NOT
SCALE FROM
THIS PRINT
(("A" X 500[19.7]) - 90[35]) 30[1.2]
12.83 .505
REF
34.79 1.370
REF
18.08 .712
REF
06
01
14.10 .555
REF
05
10
CWP-01
IPD1-05-D-K
(SEE NOTE 5)
SUB-SCR2-10-10-01
(SEE NOTE 5)
SPN-10-02
NOTES:
C
1.
REPRESENTS A CRITICAL DIMENSION.
2. NOTE MOVED.
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN MILLIMETERS. THIS DOCUMENT CONTAINS INFORMATION
TOLERANCES ARE:
PROPRIETARY NOTE
3. X.XX LENGTH IS EQUAL TO OVERALL LENGTH OF DWC-24-10-300 ("A").
4. LENGTH TOLERANCE SHALL BE ± 2% OF LENGTH.
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
5. WIRING TO BE POS 1 TO POS 1, POS 2 TO POS 2, POS 3 TO POS 3, ETC.
DECIMALS
ANGLES
2
C2
6. ASSEMBLY TO BE 100% HI-POT TESTED AT 1000V AND TO BE 100% TESTED FOR OPENS AND SHORTS;
AFTER IN PROCESS 4 FOR -D AND IN PROCESS 3 FOR -BC, THEN FINAL ASSEMBLY.
AFTER FINAL ELECTRICAL TEST, LABEL EACH ASSEMBLY WITH 1 LABEL-ET.
7. PANEL THICKNESS: 0.08[.03] - 5.2[.205].
.X: 0.3 [.01]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
.XX: 0.13 [.005]
.XXX: 0.051 [.0020]
DO NOT SCALE DRAWING
SHEET SCALE: 1:1.33333
MATERIAL:
DESCRIPTION:
H
H
SUB-SCR2-10-10-01: PBT
IPD1-05-D-K: PBT
8. ASSEMBLY TO BE SHIPPED WITH SUB-SCRX-10-01 IN SEAL-TOP BAGS, SEE FIG. 3, SHEET 2.
9. MINIMUM RETENTION FORCE: 8.9N[2 LBS].
UNSEALED 24 AWGCABLE ASSEMBLY
DWG. NO.
CONTACTS: PHOS BRONZE
SPN-10-02: PA66
10. TORQUE SPECIFICATION FOR NUT ON SUB-SCRX-10-01 IS 25 IN-LBS.
11. WIRE SHALL APPEAR IN THIS RANGE AFTER CRIMP.
SCR2-10-10-X-X.XX-XX
12. SEE DWL-05-XX-XX-X-XX.XX-XX FOR CRIMP DIMENSIONS.
SHEET 1 OF 5
BY:
LENNY K
5/10/06
13. SEE DWL-02-XX-XX-X-XX.XX-XX FOR CRIMP DIMENSIONS.
F:\DWG\MISC\MKTG\SCR2-10-10-X-X.XX-XX-MKT.SLDDRW