APPLICABLE STANDARD
-25 C to
+85 C
-10 C to +60 C
Operating
Storage temperature
range
Rating
temperature range
Voltage
AC 500 V, DC 700 V
10 A
Current
Applicable cable
SPECIFICATIONS
TEST METHOD
ITEM
REQUIREMENTS
QT AT
CONSTRUCTION
X
X
X
X
General examination
Visually and by measuring instrument.
Confirmed visually.
According to drawing.
Marking
ELECTRICAL CHARACTERISTICS
X
X
X
X
2
m MAX.
M MIN.
Contact resistance
Contact measured at DC 1 A.
1000
Insulation resistance
500
V DC.
X
X
Voltage proof
1500
V AC. for 1 min.
No breakdown.
MECHANICAL CHARACTERISTICS
Contact mating and unmating Measured with ―――
steel pin gage.
Mating and unmating forces: ― N MIN.
-
-
-
forces
Connector mating and
unmating forces
Measured with an applicable connector.
Without locking device.
Mating and unmating forces :40 N MAX.
X
Contact resistance:
4
m MAX.
Mechanical operation
Mated and unmated 2,000 times.
X
X
-
-
①No electrical discontinuity of 10 s.
②No damage, crack and looseness, of parts.
Vibration
Shock
Frequency: 10 → 55 → 10 Hz, single amplitude
0.75 mm, 5min/cycle, for 10 cycles in each of three
mutually perpedicular directions.
Acceleration: 490m/s², half sine wave pulses of 11ms. ① No electrical discontinuity of 10 s.
Performed 3 times in each of three mutually
perpendicular directions.
② No damage, crack and looseness, of parts.
X
-
ENVIRONMENTAL CHARACTERISTICS
Damp heat
Subjected to 40゚C, at a humidity of 90 to 95% for
①Insulation resistance:100 MΩ MIN (When dry).
②No damage, crack and looseness, of parts.
X
X
-
-
(Steady state)
96h.
Rapid change of temperature Temperature -55→ R/T(1) → +85 → R/T ℃
Time 30 → 2 to 3 → 30 → 2 to 3 min
for 5 cycles.
① Insulation resistance: 100 MΩ MIN.
② No damage, crack and looseness of parts.
Corrosion salt mist
Heat resistance
Cold resistance
Subjected to 5% salt spray for 48h.
Subjected to +85゚C for 96h.
Subjected to -55゚C for 96h.
No heavy corrosion which impairs functionality.
No damage, crack and looseness of parts.
No damage, crack and looseness of parts.
X
X
X
X
-
-
-
-
Resistance to soldering
heat
Soldering iron is placed to the soldering surface for No deformation or excessive looseness of
3s. (Iron tip temperature +380±10℃)
Soldered at solder temperature, +350±10℃ for
immersion duration, 3s.
terminals.
Solder ability
Soldering surface shall be free from pin-holes,
de-wetted and un-wetted areas and other defects.
No water penetration into the connector.
X
X
X
-
-
-
Sealing(2)
Subjected to a depth of 1.8m for 48h.
(IPX8)
Airtightness(2)
17.6 kPa of air pressure applied to the inside of
the mated connector for 30s.
No air bubbles emitted from the inside of the
connector.
COUNT
DESCRIPTION OF REVISIONS
DESIGNED
CHECKED
DATE
△
0
APPROVED
REMARKS
Notes (1) R/T : Room temperature
TP.KOMATSU
20221019
20221019
20221019
CHECKED
DESIGNED
HY.KOBAYASHI
HT.ZENBA
(2) Sealing and Air Tightness shall be tested in mated condition with
an applicable connector.
DRAWN
KR.SUZUKI
20220922
Unless otherwise specified, refer to IEC 60512(JIS C 5402).
Note QT:Qualification Test AT:Assurance Test X:Applicable Test
DRAWING NO.
PART NO.
CODE NO.
ELC-110769-81-00
RM15WTRZA-4P(81)
SPECIFICATION SHEET
0
1/1
HIROSE ELECTRIC CO., LTD.
CL0109-1653-5-81
△
FORM HD0011-2-1