CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Radial Lead Type, Long Life Assurance
PLS
Ultra-low ESR, High ripple current.
Load life of 5000 hours at 105°C.
Radial lead type :
Lead free flow soldering condition correspondence.
Compliant to the RoHS directive (2011/65/EU).
Long Life
PLF
PLS
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Tangent of loss angle (tan δ)
–55 to +105°C
2.5 to 16V
100 to 1500µF
20% at 120Hz, 20°C
Less than or equal to the specified value 120Hz, 20°C
at
(
1)
ESR
Less than or equal to the specified value 100kHz, 20°C
at
Leakage Current ( 2)
Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C 1.25
Z–55°C / Z+20°C 1.25
(100kHz)
(
3
)
)
Capacitance change
Within 20% of the initial capacitance value
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 5000 hours at 105°C.
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
tan δ
Endurance
(
1)
ESR
Leakage current ( 2)
(
3
Capacitance change
Within 20% of the initial capacitance value
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Damp Heat
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
tan δ
(
1)
ESR
(Steady State)
Leakage current ( 2)
After soldering the capacitor under the soldering conditions
prescribed here as preheat at 150 to 200°C for 60 to 180 seconds
and peak temperature at 265°C for 10 seconds or less, the
capacitor shall meet the specifications listed at right, provided that
its temperature profile is measured at both of terminal ends facing
the soldering side.
(
3
)
Capacitance change
Within 10% of the initial capacitance value
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
tan δ
Resistance to
Soldering Heat
(
1)
ESR
Leakage current ( 2)
Marking
Navy blue print on the case top
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Type numbering system (Example : 10V 270 F)
µ
Resin coated Case
Capacitance
1
2
3
4
5
6
7
8
9 10 11 12
Voltage(A:10V)
P L S 1 A 2 7 1 M D O 1
Size code
Configuration
Capacitance tolerance ( 20ꢀ%
φd
Series
Lot. No.
Rated capacitance
(
270µF
%
%
+0.5MAX.
15MIN
4MIN
L
Rated voltage
(
10V
Series name
Type
(mm)
Voltage
V
φ
φ
φ
φ
φ
φ
6.3 × 9L 6.3
×
10.5L
6.3
8 × 7L
8.0
6.5
3.5
0.6
8 × 9L
8.0
8.5
3.5
0.6
8 × 12L 10 × 13L
Size
φD
L
2.5
e
4
g
6.3
j
10
A
16
C
6.3
8.0
11.5
3.5
10.0
12.5
5.0
Code
8.5
2.5
0.6
10.0
2.5
0.5
P
Frequency coefficient of rated ripple current
0 Frequency0/ 120Hz 1kHz 10kHz 100kHz or more
φ
0.6
0.6
d
Coefficient
0.05
0.30
0.70
1.00
Please refer to page 20 about the end seal configuration.
Dimension table in next page.
62
5秒后页面跳转
AO3401场效应管参数、引脚图、应用原理图
BT131可控硅参数及引脚图、工作原理详解
74LS32芯片参数、引脚图及功能真值表
全球首块英伟达H200交付 黄仁勋“送货上门”
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
