4Mb: 256K x 18, 128K x 32/36
FLOW-THROUGH SYNCBURST SRAM
TQFPPINDESCRIPTIONS
x18
x32/x36
SYMBOL TYPE
DESCRIPTION
37
36
37
36
SA0
SA1
SA
Input Synchronous Address Inputs: These inputs are registered and
must meet the setup and hold times around the rising edge of
CLK.
32–35, 44–50, 32–35, 44–50,
80–82, 99,
100
81, 82, 99,
100
93
94
–
93
94
95
96
BWa#
BWb#
BWc#
BWd#
Input Synchronous Byte Write Enables: These active LOW inputs allow
individual bytes to be written and must meet the setup and hold
times around the rising edge of CLK. A byte write enable is LOW
for a WRITE cycle and HIGH for a READ cycle. For the x18 version,
BWa# controls DQa pins and DQPa; BWb# controls DQb pins and
DQPb. For the x32 and x36 versions, BWa# controls DQa pins and
DQPa; BWb# controls DQb pins and DQPb; BWc# controls DQc pins
and DQPc; BWd# controls DQd pins and DQPd. Parity is only
available on the x18 and x36 versions.
–
87
88
89
87
88
89
BWE#
GW#
CLK
Input Byte Write Enable: This active LOW input permits BYTE WRITE
operations and must meet the setup and hold times around the
rising edge of CLK.
Input Global Write: This active LOW input allows a full 18-, 32- or 36-bit
WRITE to occur independent of the BWE# and BWx# lines and must
meet the setup and hold times around the rising edge of CLK.
Input Clock: This signal registers the address, data, chip enable, byte write
enables and burst control inputs on its rising edge. All synchronous
inputs must meet setup and hold times around the clock’s rising
edge.
98
92
97
98
92
97
CE#
CE2#
CE2
Input Synchronous Chip Enable: This active LOW input is used to enable
the device and conditions the internal use of ADSP#. CE# is sampled
only when a new external address is loaded.
Input Synchronous Chip Enable: This active LOW input is used to enable
the device and is sampled only when a new external address is
loaded.
Input Synchronous Chip Enable: This active HIGH input is used to enable
the device and is sampled only when a new external address is
loaded.
86
83
86
83
OE#
Input Output Enable: This active LOW, asynchronous input enables the
data I/O output drivers.
ADV#
Input Synchronous Address Advance: This active LOW input is used to
advance the internal burst counter, controlling burst access after
the external address is loaded. A HIGH on this pin effectively causes
wait states to be generated (no address advance). To ensure use of
correct address during a WRITE cycle, ADV# must be HIGH at the
rising edge of the first clock after an ADSP# cycle is initiated.
84
84
ADSP#
Input Synchronous Address Status Processor: This active LOW input
interrupts any ongoing burst, causing a new external address to be
registered. A READ is performed using the new address,
independent of the byte write enables and ADSC#, but dependent
upon CE#, CE2 and CE2#. ADSP# is ignored if CE# is HIGH. Power-
down state is entered if CE2 is LOW or CE2# is HIGH.
(continued on next page)
4Mb: 256K x 18, 128K x 32/36 Flow-Through SyncBurst SRAM
MT58L256L18F1_F.p65 – Rev. F, Pub. 1/03 EN
MicronTechnology,Inc.,reservestherighttochangeproductsorspecificationswithoutnotice.
5
©2003,MicronTechnology,Inc.
5秒后页面跳转
MAX7219驱动8段数码管详解及数据手册关键信息
ATMEGA328P技术资料深入分析
AT24C02芯片手册管脚信息、参数分析、应用领域详解
AT24C256芯片手册参数分析、引脚说明、读写程序示例
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
