DECODER OUTPUT — SHORT FRAME
seen while DOE is high. The enable can be used to extend
the LSB to a full DDC period and/or cause the eight bits of
data to be recirculated to the output pin until the enable falls.
Figure 7 shows the timing of the decoder output in short
frame mode.
The DDO will provide the 8–bit PCM word for the decoding
rate that was selected for this frame of data on the decoder
input pins. The data is loaded into the MC145532 during one
frame, decoded on the next frame, and read during the third
frame.
STANDARDS INFORMATION
The following standards apply to the MC145532:
T1.301–1987 — 32 kbps ADPCM
T1.303–1988 — 24 kbps ADPCM
CCITT G.721–1988, G.723–1988, and G.726 — 32 kbps
and 24 kbps
DECODER OUTPUT — LONG FRAME
Figure 8 shows the timing of the decoder output in long
frame mode. Note that at least eight bits are presented to the
output, provided that at least two falling edges of DDC are
CCITT, ITU–T, TIA, and EIA documents may be obtained
by contacting Global Engineering Documents in the USA at
(800) 854–7179, or internationally at (303) 397–7956.
ABSOLUTE MAXIMUM RATINGS (Voltages Referenced to V
)
SS
This device contains circuitry to protect
against damage due to high static voltages or
Rating
DC Supply Voltage
Symbol
Value
Unit
V
DD
– 0.5 to + 7.0
V
V
electric fields; however, it is advised that
normal precautions be taken to avoid appli-
cation of any voltage higher than maximum
rated voltages to this high impedance circuit.
For proper operation it is recommended that
Voltage, Any Pin to V
DC Current, Any Pin
V
– 0.5 to V + 0.5
DD
SS
I
in
± 10
mA
°C
°C
Operating Temperature
Storage Temperature
T
A
– 40 to + 85
V
andV beconstrainedtotherangeV ≤
out SS
in out DD
in
(V or V ) ≤ V
.
T
stg
– 85 to + 150
Unused inputs must always be tied to an
appropriatelogicvoltagelevel(e.g.,eitherV
SS
or V ).
DD
RECOMMENDED OPERATING CONDITIONS (T = – 40 to + 85°C)
A
Parameter
DC Supply Voltage
Symbol
Min
Max
5.50
0.28
Unit
V
DD
4.50
—
V
Power Dissipation
P
D
W
DIGITAL CHARACTERISTICS (V
DD
= 5.0 V, T = – 40 to + 85°C)
A
Parameter
Symbol
Min
2.0
—
Max
—
Unit
V
High Level Input Voltage
Low Level Input Voltage
High Level Input Voltage
Low Level Input Voltage
Input Current
Mode, DOE, DDC, DDI, DIE, EIE, EDI, EDC, EOE
Mode, DOE, DDC, DDI, DIE, EIE, EDI, EDC, EOE
RESET, APD, SPC
V
IH
V
IL
0.8
—
V
V
IH
0.7 V
DD
V
RESET, APD, SPC
V
—
—
—
4.6
—
—
0.3 V
DD
V
IL
I
in
± 1.0
10
µA
pF
V
Input Capacitance
C
in
High Level Output Voltage (I
= – 2.0 mA)
DDO, EDO
DDO, EDO
DDO, EDO
V
OH
—
OH
Low Level Output Voltage (I
= 2.0 MA)
= 5.5 V)
V
OL
0.4
V
OL
Output Leakage Current (V
I
± 5.0
µA
DD
lkg
SWITCHING CHARACTERISTICS (V
= 5.0 V, T = – 40 to + 85°C)
A
DD
Parameter
Min
19.990
45
Max
23
Unit
MHz
%
SPC Frequency
SPC Duty Cycle
55
MC145532
4
MOTOROLA