Philips Semiconductors Linear Products
Product specification
LM111/211/311/
LM311B
Voltage comparator
1, 2, 3, 6
DC ELECTRICAL CHARACTERISTICS
Over temperature range unless otherwise specified.
LM111/LM211
LM311
Typ
2.0
LM311B
UNIT
SYMBOL
PARAMETER
TEST CONDITIONS
T =25°C, R ≤50kΩ
Min
Typ
0.7
4.0
60
Max
Min
Max
7.5
50
Min
Typ
2.0
6
Max
7.5
25
3
V
OS
Input offset voltage
3.0
10
mV
nA
A
S
3
I
I
Input offset current
Input bias current
Voltage gain
T =25°C
A
6.0
OS
BIAS
T =25°C
A
100
100
200
200
250
100
200
500
200
nA
A
V
T =25°C
A
200
200
V/mV
ns
4
Response time
T =25°C
A
LM111/211 V ≤-5mV,
IN
I =50mA
OUT
V
Saturation voltage
Strobe on current
LM311/B V ≤-10mV,
0.75
3.0
1.5
0.75
3.0
1.5
0.75
3.0
1.5
V
SAT
IN
I =50mA
OUT
T =25°C
A
I
T =25°C
A
mA
BAL/STR
LM111/211 V ≥5mV,
IN
V =35V
OUT
LM311/B V ≥10mV,
IN
6
I
Output leakage current
V =35V
OUT
0.2
10
0.2
50
0.2
50
nA
LEAKAGE
T =25°C,
A
I
=3mA
STROBE
(V– = V
= –5V)
GND
3
V
Input offset voltage
R ≤50kΩ
S
4.0
20
10
70
10
50
mV
nA
nA
OS
3
I
I
Input offset current
OS
BIAS
Input bias current
150
300
250
13.8
to
-14.7
13.8
to
-14.7
V=±15V (Pin 7 may go
V–
+0.5
V+
–1.5
V
Input voltage range
-14.5
13.0 -14.5
13.0
0.4
V
IN
to 5V)
V+ ≥ 4.5V, V- = 0
LM111/211 V ≤-6mV,
IN
6
V
OL
Saturation voltage
I
≤8mA
0.23
0.4
0.23
0.23
1.6
0.4
3.5
V
SINK
LM311/B V ≤-10mV,
IN
I
≤8mA
SINK
I
I
I
Output leakage current
Positive supply current
Negative supply voltage
V
IN
≥5mV, V =35V
OUT
0.1
5.1
4.1
0.5
6.0
5.0
µA
mA
mA
OH
CC
EE
T =25°C
A
5.1
4.1
7.5
5.0
T =25°C
A
NOTES:
1. This rating applies for ±15V supplies. The positive input voltage limit is 30V above the negative supply. The negative input voltage limit is
equal to the negative supply voltage or 30V below the positive supply, whichever is less.
2. These specifications apply for V =±15V and 0°C < T < 70°C unless otherwise specified. With the LM211, however, all temperature
S
A
specifications are limited to -25°C ≤ T ≤ 85°C and for the LM111 is limited to -55°C T < 125°C. The offset voltage, offset current, and bias
A
A
current specifications apply for any supply voltage from a single 5V supply up to ±15V supplies.
3. The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with 1mA
load. Thus, these parameters define an error band and take into account the worst case effects of voltage gain and input impedance.
4. The response time specified is for a 100mV input step with 5mV over-drive.
5. Do not short the strobe pin to ground; it should be current driven at 3mA to 5mA.
6. LM311B, all parameters are at V+ = 3V ±10%, V– = GND = 0V.
275
August 31, 1994