KMM372F160(8)0CK/CS
DRAM MODULE
KMM372F160(8)0CK/CS EDO Mode
16M x 72 DRAM DIMM with ECC Using 16Mx4, 4K & 8K Refresh, 3.3V
FEATURES
• Part Identification
GENERAL DESCRIPTION
The Samsung KMM372F160(8)0C is a 16Mx72bits Dynamic
RAM high density memory module. The Samsung
KMM372F160(8)0C consists of eighteen CMOS 16Mx4bits
DRAMs in SOJ/TSOP-II 400mil packages and two 16 bits
driver IC in TSSOP package mounted on a 168-pin glass-
epoxy substrate. A 0.1 or 0.22uF decoupling capacitor is
mounted on the printed circuit board for each DRAM. The
KMM372F160(8)0C is a Dual In-line Memory Module and is
intended for mounting into 168 pin edge connector sockets.
Part number
PKG
SOJ
Ref.
4K
CBR Ref.
ROR Ref.
8K/64ms
KMM372F1600CK
4K/64ms
KMM372F1600CS TSOP
KMM372F1680CK SOJ
KMM372F1680CS TSOP
8K
4K/64ms
• Extended Data Out Mode Operation
• CAS-before-RAS Refresh capability
• RAS-only and Hidden refresh capability
• LVTTL compatible inputs and outputs
• Single 3.3V±0.3V power supply
PERFORMANCE RANGE
Speed
tRAC
50ns
60ns
tCAC
18ns
20ns
tRC
tHPC
20ns
25ns
• JEDEC standard pinout & Buffered PDpin
• Buffered input except RAS and DQ
• PCB : Height(1250mil), double sided component
-5
84ns
104ns
-6
PIN CONFIGURATIONS
PIN NAMES
Pin Front Pin Front Pin Front Pin Back Pin Back Pin Back
Pin Names
Function
A0, B0, A1 - A11 Address Input(4K ref.)
A0, B0, A1 - A12 Address Input(8K ref.)
57
58
59
60
61
62
63
64
65
1
2
3
4
5
6
7
8
9
VSS
29 *CAS2
DQ22 85
DQ23 86 DQ36 114 *RAS1 142 DQ59
87 DQ37 115 RFU 143 VCC
DQ24 88 DQ38 116 VSS 144 DQ60
VSS 113 *CAS3 141 DQ58
DQ0 30 RAS0
DQ0 - DQ71
W0, W2
OE0, OE2
RAS0, RAS2
CAS0, CAS4
VCC
Data In/Out
DQ1 31
DQ2 32
DQ3 33
OE0
VSS
A0
VCC
Read/Write Enable
Output Enable
RFU 89 DQ39 117
RFU 90 VCC 118
RFU 91 DQ40 119
RFU 92 DQ41 120
DQ25 93 DQ42 121
A1
A3
A5
A7
A9
145 RFU
146 RFU
147 RFU
148 RFU
149 DQ61
VCC
34
A2
Row Address Strobe
Column Address Strobe
Power(+3.3V)
DQ4 35
DQ5 36
DQ6 37
A4
A6
A8
10 DQ7 38
11 DQ8 39
12
13 DQ9 41 RFU
14 DQ10 42 RFU
15 DQ11 43
16 DQ12 44
17 DQ13 45 RAS2
18 46 CAS4
19 DQ14 47 *CAS6
20 DQ15 48
21 DQ16 49
22 DQ17 50 RSVD
23 51 RSVD
24 RSVD 52 DQ18
25 RSVD 53 DQ19
A10
A12
VCC
66 DQ26 94 DQ43 122 A11 150 DQ62
VSS
Ground
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
DQ27 95 DQ44 123 *A13 151 DQ63
96 VSS 124 VCC 152 VSS
DQ28 97 DQ45 125 RFU 153 DQ64
DQ29 98 DQ46 126 B0 154 DQ65
NC
No Connection
Presence Detect Enable
Presence Detect
ID bit
VSS
40
VSS
PDE
PD1 - 8
ID0 - 1
VSS
OE2
DQ30 99 DQ47 127 VSS 155 DQ66
DQ31 100 DQ48 128 RFU 156 DQ67
VCC 101 DQ49 129 *RAS3 157 VCC
DQ32 102 VCC 130 *CAS5 158 DQ68
DQ33 103 DQ50 131 *CAS7 159 DQ69
DQ34 104 DQ51 132 PDE 160 DQ70
DQ35 105 DQ52 133 VCC 161 DQ71
VSS 106 DQ53 134 RSVD 162 VSS
PD1 107 VSS 135 RSVD 163 PD2
PD3 108 RSVD 136 DQ54 164 PD4
PD5 109 RSVD 137 DQ55 165 PD6
PD7 110 VCC 138 VSS 166 PD8
ID0 111 RFU 139 DQ56 167 ID1
VCC 112 *CAS1 140 DQ57 168 VCC
RSVD
Reserved Use
VCC
RFU
Reserved for Future Use
Pins marked ¢*¢ are not used in this module.
W2
VCC
PD & ID Table
Pin
50NS
60NS
VSS
PD1
PD2
PD3
PD4
PD5
PD6
PD7
PD8
1
1
1
1
1
0
0
0
1
1
1
1
1
1
1
0
26
27
VCC
W0
54
VSS
55 DQ20
28 CAS0 56 DQ21
NOTE : A12 is used for only KMM372F1680CK/CS (8K Ref.)
ID0
ID1
0
0
0
0
PD Note :PD & ID Terminals must each be pulled up through a register to VCC at the next higher
level assembly. PDs will be either open (NC) or driven to VSS via on-board buffer circuits.
ID Note : IDs will be either open (NC) or connected directly to VSS without a buffer.
PD : 0 for Vol of Drive IC & 1 for N.C
ID : 0 for Vss & 1 for N.C