2.5 VOLT HIGH-SPEED TeraSyncTM FIFO 36-BIT CONFIGURATIONS
1,024 x 36, 2,048 x 36, 4,096 x 36,
8,192 x 36, 16,384 x 36, 32,768 x 36,
65,536 x 36, 131,072 x 36 and 262,144 x 36
IDT72T3645, IDT72T3655, IDT72T3665,
IDT72T3675, IDT72T3685, IDT72T3695,
IDT72T36105, IDT72T36115, IDT72T36125
FEATURES:
Empty and Almost-Full flags
• Choose among the following memory organizations:
• Separate SCLK input for Serial programming of flag offsets
• User selectable input and output port bus-sizing
- x36 in to x36 out
- x36 in to x18 out
- x36 in to x9 out
IDT72T3645
IDT72T3655
IDT72T3665
IDT72T3675
IDT72T3685
IDT72T3695
IDT72T36105
IDT72T36115
IDT72T36125
1,024 x 36
2,048 x 36
4,096 x 36
8,192 x 36
16,384 x 36
32,768 x 36
65,536 x 36
131,072 x 36
262,144 x 36
- x18 in to x36 out
- x9 in to x36 out
• Big-Endian/Little-Endian user selectable byte representation
• Auto power down minimizes standby power consumption
• Master Reset clears entire FIFO
• Partial Reset clears data, but retains programmable settings
• Empty, Full and Half-Full flags signal FIFO status
• Up to 225 MHz Operation of Clocks
• User selectable HSTL/LVTTL Input and/or Output
• 2.5V LVTTL or 1.8V, 1.5V HSTL Port Selectable Input/Ouput voltage • Select IDT Standard timing (using EF and FF flags) or First Word
• 3.3V Input tolerant Fall Through timing (using OR and IR flags)
• Read Enable & Read Clock Echo outputs aid high speed operation • Output enable puts data outputs into high impedance state
• User selectable Asynchronous read and/or write port timing
• Mark & Retransmit, resets read pointer to user marked position
• Write Chip Select (WCS) input enables/disables Write operations
• Read Chip Select (RCS) synchronous to RCLK
• JTAG port, provided for Boundary Scan function
• Available in 208-pin (17mm x 17mm) or 240-pin (19mm x 19mm)
Plastic Ball Grid Array (PBGA)
• Easily expandable in depth and width
• Programmable Almost-Empty and Almost-Full flags, each flag can • Independent Read and Write Clocks (permit reading and writing
default to one of eight preselected offsets
simultaneously)
• Program programmable flags by either serial or parallel means
• Selectable synchronous/asynchronous timing modes for Almost-
• High-performance submicron CMOS technology
• Industrial temperature range (–40°C to +85°C) is available
FUNCTIONALBLOCKDIAGRAM
D0
-Dn
(x36, x18 or x9)
LD SEN
SCLK
WEN
WCLK/WR
WCS
INPUT REGISTER
OFFSET REGISTER
FF/IR
PAF
EF/OR
PAE
HF
FWFT/SI
PFM
FSEL0
FSEL1
WRITE CONTROL
LOGIC
ASYW
FLAG
LOGIC
RAM ARRAY
1,024 x 36, 2,048 x 36
4,096 x 36, 8,192 x 36
16,384 x 36, 32,768 x 36
65,536 x 36, 131,072 x36
262,144 x 36
WRITE POINTER
BE
CONTROL
LOGIC
READ POINTER
IP
BM
IW
OW
BUS
CONFIGURATION
RT
READ
CONTROL
LOGIC
MARK
ASYR
MRS
PRS
OUTPUT REGISTER
RESET
LOGIC
TCK
TRST
TMS
TDO
JTAG CONTROL
(BOUNDARY SCAN)
RCLK/RD
REN
RCS
TDI
Vref
WHSTL
RHSTL
SHSTL
HSTL I/0
CONTROL
EREN
OE
5907 drw01
Q0 -Qn (x36, x18 or x9)
ERCLK
IDT and the IDT logo are registered trademarks of Integrated Device Technology, Inc. The TeraSync FIFO is a trademark of Integrated Device Technology, Inc.
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
SEPTEMBER 2003
1
2003 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice.
DSC-5907/17