HV57708
32 MHz, 64-Channel Serial To Parallel Converter
With Push-Pull Outputs
Ordering Information
Package Options
Device
80 Lead Quad
Ceramic Gullwing
80 Lead Quad
Plastic Gullwing
80 Lead Quad
Ceramic Gullwing
Die
(MIL-STD-883 Processed*)
(MIL-STD-883 Processed*)
HV57708
HV57708DG
HV57708PG
RBHV57708DG
HV57708X
* For Hi-Rel process flows, refer to page 5-3 of the Databook.
Features
General Description
The HV577 is a low-voltage serial to high-voltage parallel con-
verter with push-pull outputs. This device has been designed for
useasadriverforelectroluminescentdisplays.Itcanalsobeused
in any application requiring multiple output high-voltage current
sourcing and sinking capability such as driving plasma panels,
vacuum fluorescent displays, or large matrix LCD displays.
❏
❏
❏
❏
❏
❏
❏
❏
❏
❏
Processed with HVCMOS® technology
5V CMOS logic
Output voltages up to 80V
Low power level shifting
32MHz equivalent data rate
Latched data outputs
The device has 4 parallel 16-bit shift registers, permitting data
rates 4X the speed of one ( they are clocked together). There are
also 64 latches and control logic to perform the polarity select and
blanking of the outputs. HVout1 is connected to the first stage of
the first shift register through the polarity and blanking logic. Data
is shifted through the shift registers on the logic low to high
transition of the clock. The DIR pin causes CCW shifting when
connected to GND, and CW shifting when connected to VDD. A
data output buffer is provided for cascading devices. This output
reflects the current status of the last bit of the shift register
(HVOUT64). Operation of the shift register is not affected by the LE
(latch enable), BL (blanking), or the POL (polarity) inputs. Trans-
fer of data from the shift registers to the latches occurs when the
LE (latch enable) input is high. The data in the latches is stored
when LE is low.
Forward and reverse shifting options (DIR pin)
Diode to VPP allows efficient power recovery
Outputs may be hot switched
Hi-Rel processing available
Absolute Maximum Ratings
Supply voltage, VDD
1
-0.5V to +7.5V
1
Output voltage, VPP
-0.5V to +90V
-0.3V to VDD +0.3V
1.5A
Logic input levels1
Ground current2
Continuous total power dissipation3
Plastic
Ceramic
1200mW
1900mW
Operating temperature range
Storage temperature range
Plastic
Ceramic
-40 to 85°C
-55°C to 125°C
-65°C to +150°C
260°C
Lead temperature 1.6mm (1/16 inch)
from case for 10 seconds
Notes:
1. All voltages are referenced to GND.
2. Limited by the total power dissipated in the package.
3. For operation above 25°C ambient derate linearly to maximum operating
temperature at 20mW/°C for plastic and at 19mW/°C for ceramic.
For detailed circuit and application information, please refer
to application note AN-H3.
02/96/022
Supertex Inc. does not recommend the use of its products in life support applications and will not knowingly sell its products for use in such applications unless it receives an adequate "products liability
indemnification insurance agreement." Supertex does not assume responsibility for use of devices described and limits its liability to the replacement of devices determined to be defective due to
workmanship. No responsibility is assumed for possible omissions or inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications, refer to the
Supertex website: http://www.supertex.com. For complete liability information on all Supertex products, refer to the most current databook or to the Legal/Disclaimer page on the Supertex website.
1