HS-22620RH
Data Sheet
August 1999
File Number 4349.1
Rad Hard Dual, Wideband, High Input
Impedance Uncompensated Operational
Amplifier
Features
• Electrically Screened to SMD # 5962-97512
• QML Qualified per MIL-PRF-38535 Requirements
• High Input Impedance . . . . . . . . . . . . . . . . . . 65MΩ (Min)
• High Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . 80kV/V (Min)
• High Slew Rate . . . . . . . . . . . . . . . . . . . . . . 20V/µs (Min)
• Low Input Bias Current. . . . . . . . . . . . . . . . . . 50nA (Max)
• Low Input Offset Voltage . . . . . . . . . . . . . . . . . 6mV (Max)
The HS-22620RH is a radiation hardened, dual bipolar
operational amplifier that features very high input impedance
coupled with wideband AC performance. The high
resistance of the input stage is complemented by low offset
o
voltage (6mV Max at 25 C) and low bias current (50nA Max
o
at 25 C) to facilitate accurate signal processing. Offset
voltage can be reduced further by means of an external
nulling potentiometer. The stable closed loop gains greater
o
• Wide Gain Bandwidth Product (A ≥ 10) . . . . .100MHz (Typ)
than 10, the 20V/µs minimum slew rate at 25 C and the
V
o
80kV/V minimum open loop gain at 25 C, enable the
• Output Short Circuit Protection
HS-22620RH to perform high gain amplification of very fast,
wideband signals. These dynamic characteristics, coupled
with fast settling times, make these amplifiers ideally suited
to pulse amplification designs as well as high frequency or
video applications. The frequency response of the amplifier
can be tailored to exact design requirements by means of an
external bandwidth control capacitor.
5
• Total Dose . . . . . . . . . . . . . . . . . . . . . . . . . . .3 x 10 RAD(Si)
Applications
• Video and RF Amplifiers
• Pulse Amplifiers
• High-Q Active Filters
• High Speed Comparators
Specifications for Rad Hard QML devices are controlled
by the Defense Supply Center in Columbus (DSCC). The
SMD numbers listed here must be used when ordering.
Ordering Information
Detailed Electrical Specifications for these devices are
contained in SMD 5962-97512. A “hot-link” is provided
on our homepage for downloading.
INTERNAL
TEMP. RANGE
o
ORDERING NUMBER
5962F9751201V9A
5962F9751201VXC
MKT. NUMBER
( C)
www.intersil.com/spacedefense/space.asp
HS0-22620RH-Q
HS9-22620RH-Q
25
-55 to 125
-55 to 125
HS9-22620RH/PROTO HS9-22620RH/PROTO
Pinout
HS-22620RH
(FLATPACK)
TOP VIEW
(1) BAL 2A
(2) BAL 1A
(3) +IN A
(4) -IN A
V
V
A (18)
A (17)
CC
EE
OUT A (16)
COMP A (15)
WEB (14)
+
-
(5) OPEN
(6) -IN B
COMP B (13)
OUT B (12)
VEE B (11)
-
+
(7) +IN B
(8) BAL 1B
(9) BAL 2B
V
B (10)
CC
NOTE: Refer to SMD, Figure 1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999
1