Radiation Hardened Quad Differential Line Receiver
HS-26C32RH, HS-26C32EH
Features
The Intersil HS-26C32RH, HS-26C32EH are differential line
receivers designed for digital data transmission over balanced
lines and meets the requirements of EIA Standard RS-422.
Radiation hardened CMOS processing assures low power
consumption, high speed, and reliable operation in the most
severe radiation environments.
• Electrically screened to SMD #5962-95689
• QML qualified per MIL-PRF-38535 requirements
• 1.2 micron radiation hardened CMOS
- Total dose . . . . . . . . . . . . . . . . . . . . . . . . 300 krad(Si) (max)
• Latch-up free
The HS-26C32RH, HS-26C32EH have an input sensitivity
typically of 200mV over the common mode input voltage
range of ±7V. The receivers are also equipped with input fail
safe circuitry, which causes the outputs to go to a logic “1”
when the inputs are open. Enable and Disable functions are
common to all four receivers.
• EIA RS-422 compatible inputs
• CMOS compatible outputs
• Input fail safe circuitry
• High impedance inputs when disabled or powered down
• Low power dissipation 138mW standby (max)
• Single 5V supply
Specifications for Rad Hard QML devices are controlled by the
Defense Logistics Agency Land and Maritime (DLA). The SMD
numbers listed in the “Ordering Information” table must be
used when ordering.
• Full -55°C to +125°C military temperature range
Applications
• Line receiver for MIL-STD-1553 serial data bus
Detailed Electrical Specifications for these devices are
contained in SMD 5962-95689. A “hot-link” is provided on our
homepage for downloading
Ordering Information
ORDERING NUMBER
INTERNAL
MKT. NUMBER
PART
MARKING
TEMP. RANGE
(°C)
PACKAGE
(Pb-free)
PKG.
DWG. #
(Note 1)
5962F9568901QEC
5962F9568901QXC
5962F9568901V9A
HS1-26C32RH-8
Q 5962F95 68901QEC
Q 5962F95 68901QXC
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
16 Ld SBDIP
16 Ld FLATPACK
Die
D16.3
K16.A
HS9-26C32RH-8
HS0-26C32RH-Q
HS0-26C32RH/SAMPLE HS0-26C32RH/SAMPLE
Die
5962F9568901VEC
5962F9568901VXC
HS1-26C32RH/PROTO
HS9-26C32RH/PROTO
5962F9568903VEC
5962F9568903VXC
5962F9568903V9A
5962F9568901VYC
HS1-26C32RH-Q
Q 5962F95 68901VEC
Q 5962F95 68901VXC
HS1- 26C32RH /PROTO
HS9- 26C32RH /PROTO
Q 5962F95 68903VEC
Q 5962F95 68903VXC
Q 5962F95 68903V9A
Q 5962F95 68901VYC
16 Ld SBDIP
16 Ld FLATPACK
16 Ld SBDIP
16 Ld FLATPACK
16 Ld SBDIP
16 Ld FLATPACK
Die
D16.3
K16.A
D16.3
K16.A
D16.3
K16.A
HS9-26C32RH-Q
HS1-26C32RH/PROTO
HS9-26C32RH/PROTO
HS1-26C32EH-Q
HS9-26C32EH-Q
HS0-26C32EH-Q
HS9G-26C32RH-Q (Note 2)
16 Ld FLATPACK
16 Ld FLATPACK
K16.A
K16.A
HS9G-26C32RH/PROTO HS9G-26C32RH/PROTO (Note 2) HS9G-26C32RH/PROTO
NOTES:
1. These Intersil Pb-free Hermetic packaged products employ 100% Au plate - e4 termination finish, which is RoHS compliant and compatible with both
SnPb and Pb-free soldering operations.
2. The lid of these packages are connected to the ground pin of the device.
May 28, 2013
FN3402.5
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 2012, 2013. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
1