HMC560LM3
v00.0705
GaAs MMIC FUNDAMENTAL
SMT MIXER, 24 - 40 GHz
Recommended SMT Attachment Technique
Preparation & Handling of the LM3 Millimeterwave Package for Surface Mounting
225
The HMC LM3 package was designed to be compatible with high
200
volume surface mount PCB assembly processes. The LM3 package
7
requires a specific mounting pattern to allow proper mechanical
attachment and to optimize electrical performance at millimeterwave
frequencies. This PCB layout pattern can be found on each LM3
product data sheet. It can also be provided as an electronic drawing
upon request from Hittite Sales & Application Engineering.
175
150
125
100
75
50
Follow these precautions to avoid permanent damage:
25
Cleanliness: Observe proper handling procedures to ensure clean
devices and PCBs. LM3 devices should remain in their original
0
1
2
3
4
5
6
7
8
TIME (min)
packaging until component placement to ensure no contamination or damage to RF, DC & ground contact areas.
Static Sensitivity: Follow ESD precautions to protect against ESD strikes.
General Handling: Handle the LM3 package on the top with a vacuum collet or along the edges with a sharp pair
of bent tweezers. Avoiding damaging the RF, DC, & ground contacts on the package bottom. Do not apply excess
pressure to the top of the lid.
Solder Materials & Temperature Profile: Follow the information contained in the application note. Hand soldering is
not recommended. Conductive epoxy attachment is not recommended.
Solder Paste: Solder paste should be selected based on the user’s experience and be compatible with the metallization
systems used. See the LM3 data sheet Outline drawing for pin & ground contact metallization schemes.
Solder Paste Application: Solder paste is generally applied to the PCB using either a stencil printer or dot placement.
The volume of solder paste will be dependent on PCB and component layout and should be controlled to ensure
consistent mechanical & electrical performance. Excess solder may create unwanted electrical parasitics at high
frequencies.
Solder Reflow: The soldering process is usually accomplished in a reflow oven but may also use a vapor phase
process. A solder reflow profile is suggested above.
Prior to reflowing product, temperature profiles should be measured using the same mass as the actual assemblies.
The thermocouple should be moved to various positions on the board to account for edge and corner effects and
varying component masses. The final profile should be determined by mounting the thermocouple to the PCB at the
location of the device.
Follow solder paste and oven vendor’s recommendations when developing a solder reflow profile. A standard profile
will have a steady ramp up from room temperature to the pre-heat temperature to avoid damage due to thermal shock.
Allow enough time between reaching pre-heat temperature and reflow for the solvent in the paste to evaporate and the
flux to completely activate. Reflow must then occur prior to the flux being completely driven off. The duration of peak
reflow temperature should not exceed 15 seconds. Packages have been qualified to withstand a peak temperature of
235°C for 15 seconds. Verify that the profile will not expose device to temperatures in excess of 235°C.
Cleaning: A water-based flux wash may be used.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
7 - 425
5秒后页面跳转
NTC热敏电阻与PTC热敏电阻的应用原理及应用范围
GTO与普通晶闸管相比为什么可以自关断？为什么普通晶闸管不能呢？从GTO原理、应用范围带你了解原因及推荐型号
LF353数据手册解读：特性、应用、封装、引脚说明、电气参数及替换型号推荐
A4950资料手册解读：特性、应用、封装、引脚功能、电气参数及代换型号
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
