HIP1011D
Data Sheet
November 1999
File Number 4725.1
Dual PCI Hot Plug Controller
Features
The HIP1011D is the first IC available for independent
control of two PCI Hot Plug slots. The HIP1011D has all the
features and functionality of two single PCI Hot Plug slot
controllers such as the HIP1011A but in the same foot print
area.
• Independent Power Control of 2 PCI Slots
• Turn-Off Delay Time Adjustability
• Internal MOSFET Switches for +12V and -12V Outputs
• µP Interface for On/Off Control and Fault Reporting
• Adjustable Overcurrent Protection for All Eight Supplies
• Provides Fault Isolation
The HIP1011D is designed to be physically placed in close
proximity to two adjacent PCI slots servicing each
independently but reducing layout complexity and placement
costs in assembly. It creates two independent power control
solutions with discrete power MOSFETs and a few passive
components. The four supplies +5V, +3.3V, +12V, and -12V
for each slot are independently controlled. There are four
integrated current sensing switches for the +12V and -12V
and for the +5V and +3.3V supplies overcurrent protection is
provided by sensing the voltage across external current-
sense resistors. In addition, on-chip references are used to
monitor the +5V, +3.3V and +12V outputs for undervoltage
conditions. The two PWRON inputs control the state of the
switches, one each for slot A and slot B outputs. During an
overcurrent condition on any output, or an undervoltage
condition on the +5V, +3.3V or +12V outputs, a LOW (0V) is
asserted on the associated FLTN output and all associated
switches are latched-off. The outputs servicing the adjacent
slot are unaffected.
• Adjustable Turn-On Slew Rate
• Minimum Parts Count Solution
• No Charge Pump
• 100ns Response Time to Over Current
Applications
• PCI Hot-Plug
Ordering Information
TEMP.RANGE
PKG.
NO.
o
PART NUMBER
HIP1011DCA
( C)
PACKAGE
28 Ld SSOP
0 to 70
0 to 70
M28.15
HIP1011DCA-T
Tape and Reel
The time to FLTN signal going LOW and MOSFET latch off
is user determined by a single capacitor from each FLTN pin
to ground. This added feature enables the HIP1011D to
ignore system noise transients. The FLTN latch is cleared
when the PWRON input is toggled low again. During initial
power-up of the main VCC supply (+12V), the PWRON input
is inhibited from turning on the switches, and the latch is held
in the Reset state until the VCC input is greater than 10V.
Pinout
HIP1011D
(SSOP)
TOP VIEW
M12VO_2
M12VG_2
PWRON_2
FLTN_2
1
2
28 M12VIN_2
27 3VISEN_2
26 3VS_2
3
25 5VISEN_2
4
User programmability of the overcurrent threshold and turn-
on slew rate is provided. A resistor connected to the OCSET
pin programs the overcurrent threshold for both slots.
Capacitors connected to the gate pins set the turn-on rate.
VSS
24
23
22
21
20
19
18
17
16
15
5VS_2
5
12VG_2
12VO_2
12VO_1
12VG_1
OCSET
3V5VG_2
12VIN_2
12VIN_1
3V5VG_1
5VS_1
6
7
8
9
10
11
12
13
14
FLTN_1
5VISEN_1
3VS_1
PWRON_1
M12VG_1
M12VO_1
3VISEN_1
M12VIN_1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999
1