HIP1011A
®
Data Sheet
November 16, 2004
FN4631.5
PCI Hot Plug Controller
Features
The HIP1011A is the second PCI Hot Plug Voltage bus
control IC from Intersil. A drop-in alternative to the widely
used HIP1011, the HIP1011A has the same form, fit and
function but additionally features an adjustable latch-off time
of the MOSFET switches and fault reporting.
• Adjustable Delay Time for Turn-Off and Fault Reporting
• Controls All PCI Supplies: +5V, +3.3V, +12V, -12V
• Internal MOSFET Switches for +12V and -12V Outputs
• µP Interface for On/Off Control and Fault Reporting
• Adjustable Overcurrent Protection for All Supplies
• Provides Fault Isolation
Like the HIP1011, the HIP1011A creates a small and simple
yet complete power control solution with discrete power
MOSFETs and a few passive components. Four
independent supplies are controlled, +5V, +3.3, +12V, and
-12V. The +12V and -12V switches are integrated. For the
+5V and +3.3V supplies, overcurrent (OC) protection is
provided by sensing the voltage across external current-
sense resistors. For the +12V and -12V supplies OC
protection is provided internally. In addition, an on-chip
reference is used to monitor the +5V, +3.3V and +12V
outputs for undervoltage (UV) conditions. The PWRON input
controls the state of the switches. During an OC condition on
any output, or a UV condition on the +5V, +3.3V or +12V
outputs, a LOW (0V) is asserted on the FLTN output and all
MOSFETs are latched-off. The time to FLTN signal going
LOW and MOSFET latch-off is determined by a single
capacitor from the FLTN pin to ground. This added feature
allows the system OS to complete housekeeping activities in
preparation for an unplanned shut down of the affected card.
The FLTN latch is cleared when the PWRON input is toggled
low again. During initial power-up of the main VCC supply
(+12V), the PWRON input is inhibited from turning on the
switches, and the latch is held in the Reset state until the
VCC input is greater than 10V.
• Adjustable Turn-On Slew Rate
• Minimum Parts Count Solution
• No Charge Pump
• Pb-Free Available (RoHS Compliant)
Applications
• PCI Hot Plug
• CompactPCI
Ordering Information
TEMP. RANGE
PKG.
DWG. #
o
PART NUMBER
( C)
PACKAGE
HIP1011ACB
0 to 70
0 to 70
16 Ld SOIC
M16.15
M16.15
HIP1011ACBZA
(See Note)
16 Ld SOIC
(Pb-free)
HIP1011ACB-T
0 to 70
0 to 70
Tape and Reel
HIP1011ACBZA-T
(See Note)
Tape and Reel (Pb-free)
User programmability of the overcurrent threshold, fault
reporting response time, latch-off response time and turn-on
slew rate is provided. A resistor connected to the OCSET pin
programs the OC threshold. A capacitor may be added to the
FLTN pin to adjust both the delay time to reporting a fault
and the latch-off of the supplies after an OC or UV event.
Capacitors connected to the gate pins set the turn-on rate. In
addition the HIP1011A has also been enhanced to tolerate
spurious system noise.
NOTE: Intersil Pb-free products employ special Pb-free material sets;
molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with
both SnPb and Pb-free soldering operations. Intersil Pb-free products
are MSL classified at Pb-free peak reflow temperatures that meet or
exceed the Pb-free requirements of IPC/JEDEC J STD-020C.
Pinout
HIP1011A
(SOIC)
TOP VIEW
1
2
3
4
5
6
7
8
M12VO
M12VG
M12VIN
FLTN
16
15
3V5VG
14 12VG
13 GND
12 12VO
11 5VISEN
10 5VS
V
CC
12VIN
3VISEN
3VS
OCSET
9
PWRON
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2000, 2004. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
替代型号
如果您发现信息不准确，
