HIP0082, HIP0084
Quad Power Drivers with
Serial Diagnostic Interface
PRELIMINARY
May 1998
Features
Description
• Low Side Power MOSFET Output Drivers
The HIP0082 and HIP0084 Quad Power Drivers contain four
individually protected NDMOS transistor switches to drive
inductive and resistive loads such as: fuel injectors, relays,
solenoids, etc. The outputs are low-side switches driven by
active-low CMOS logic inputs. Each output is protected
against excessive current due to a short-circuit. Internal
drain-to-gate zener diodes provide output clamping for over
voltage. An integrated charge pump allows operation from a
single 5V logic supply. Diagnostic circuits provide ground
short (SG), supply short (SC) and open load (OL) detection
for each of the four output stages and indicate over tempera-
ture. Diagnostic information may be read via a synchronous
serial interface. Six bits of write/store data sets a long or
short OL fault delay time for each output and sets Outputs 3
and 4 to a 2A or 5A current shutdown threshold. The
HIP0084 is specified with controlled slew rate switching.
- Output Voltage Clamp (Typ) . . . . . . . . . . . . . . . . 80V
- Maximum Output Current . . . . . . . . . . . . . . . . 5A/2A
o
- Output r
(T = 150 C) (Max) . . . . .0.57Ω/0.62Ω
J
DS(ON)
• Controlled Slew Rate Switching (HIP0084)
• Single Pulse Energy Rating . . . . . . . . . . . . . . . . . 70mJ
• Programmable Output Over Current Shutdown Threshold
- Bit Select 2A or 5A on Outputs 3 and 4
• Output Protection
- Output Over Current Shutdown
- Output Over Voltage Clamp
- Over Temperature Diagnostic Feedback
• Diagnostics for Shorts, Opens and Over Temperature
• Synchronous Serial Interface with
- 22-Bit Serial Diagnostic Register
- SPI Compatible Interface
Both types are fabricated in a Power BiMOS IC process and
are intended for use in automotive and other applications with a
wide range of temperature and electrical stress. They are par-
ticularly suited for driving high-current inductive loads requiring
high breakdown voltage and high output current. Both types
available in the 15 lead Power SIP or 20 lead PSOP packages
with low thermal resistance for high power applications.
• Single 5V Supply Operation with CMOS Logic Inputs
• Supply Current, I , Full Load (Typ) . . . . . . . . . <10mA
CC
• Low θ Power SIP Packages
JC
o
o
SIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 C/W
PSOP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 C/W
Ordering Information
o
o
• -40 C to 125 C Operating Temperature
PART
NUMBER
TEMP.
RANGE(°C)
PKG.
NO.
Applications
PACKAGE
15 Ld SIP
HIP0082AS1
HIP0084AS1
HIP0082AS2
HIP0082AB
HIP0084AB
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
Z15.05A
Z15.05A
Z15.05B
M20.433
M20.433
• Drivers For
- Solenoids
- Relays
• System Use
15 Ld SIP
- Injectors
- Steppers
- Automotive
- Appliances
- Industrial
- Robotics
15 Ld SIP
20 Ld PSOP
20 Ld PSOP
- Power Output - Motors
- Lamps
- Displays
Pinouts
HIP0082, HIP0084 (SIP)
HIP0082, HIP0084 (PSOP W/HEAT SLUG)
TOP VIEW
TOP VIEW
HEAT SINK TAB INTERNALLY CONNECTED
INTEGRAL COPPER
TO PIN 8 GROUND (V
)
SS
HEAT SINK ‘SLUG’
FOR PCB CONTACT
OR EXT. HEAT SINK
15
14
13
12
11
10
9
IN3
OUT3
IN1
OUT1
R/W
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
GND (SLUG)
IN4
GND (SLUG)
IN3
OUT3
IN1
OUT4
IN2
V
CC
RST
GND (V
GND (V
)
GND (V
OUT1
R/W
)
SS
)
SS
8
SS
OUT2
CS
CLK
7
6
5
TXD
CLK
CS
V
CC
4
3
TXD
GND (SLUG)
RST
GND (SLUG)
OUT2
IN2
2
1
OUT4
IN4
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
File Number 3643.4
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
1