GLS85LS1xxxG / GLS85LS1xxxQ
Industrial Grade SATA NANDrive™ EX Series
Factsheet 01.000
July 2019
Features
• Expanded Data Protection
• Industry Standard Serial ATA (SATA) Host
–
Added data security through user-selectable
protection zones
Interface
–
–
–
–
SATA 1.5Gb/s, 3Gb/s and 6Gb/s
SATA Revision 3.2
ATA/ATAPI-8 compliant
–
Secure Erase (data sanitization)
• 20-Byte Serial Number
Supports 48-bit address feature set
–
–
Factory pre-programmed 10-Byte unique ID
User-programmable 10-Byte ID
• Performance
• Supports SMART and TRIM Commands
• Robust Built-in ECC
• Thermal Throttling
–
–
Sequential data read: Up to 470 MByte/sec*
Sequential data write: Up to 340 MByte/sec*
* 128 KByte transfer size tested in VDBench on Linux
• Power Management
• Native Command Queuing (NCQ)
–
–
–
3.3V and 1.0V power supply
Host initialized power management (HIPM)
Device initialized power management (DIPM)
–
Up to 32 commands
• NAND Configuration
–
–
1 bit per cell (SLC)
Designed with Greenliant’s advanced
EnduroSLC™ Technology
Power Specifications1)
•
–
Active mode:
128GB: Up to 2180mW
64GB: Up to 1800mW
32GB: Up to 1980mW
16GB: Up to 1540mW
8GB: Up to 1200mW
4GB: Up to 1200mW
Idle / Standby mode: <355mW (typical)
DevSleep mode: <70mW (typical)
• High Endurance
–
–
GLS85LS1xxxG: 50K P/E cycles
GLS85LS1xxxQ: 100K P/E cycles
•
Operating Temperature Range
Industrial: -40°C to 85°C
• FBGA package
14.0 mm x 24.0 mm x 1.40 mm, 145-ball,
1.0 mm ball pitch, LBJE
–
–
–
–
• All Devices are RoHS Compliant
Product Description
The GLS85LS1xxxG / GLS85LS1xxxQ Industrial
Grade SATA NANDrive™ EX Series devices (referred
to as “SATA NANDrive” in this factsheet) are fully
integrated solid state drives. They combine an
advanced Greenliant NAND controller and 4, 8, 16, 32,
64 or 128 GBytes of NAND flash in a multi-chip
package. These products are ideal for embedded and
portable applications that require a smaller form factor
and reliable data storage.
The integrated NAND flash controller with built-in
advanced
NAND
management
firmware
communicates with the host through the standard
SATA protocol. It does not require any additional or
proprietary software such as the Flash File System
(FFS) and Memory Technology Driver (MTD).
SATA NANDrive is pre-programmed with a 10-Byte
unique serial ID and has the option of programming
an additional 10-Byte serial ID for even greater
system security.
SATA-interface solid state mass storage technology is
widely used in industrial PCs, single board computers,
servers, networking appliances, HMI and digital
SATA NANDrive’s advanced NAND management
technology enhances data reliability and security,
improves endurance and accurately estimates the
remaining life of the NAND flash devices. This
innovative technology combines robust NAND
controller hardware error correction capabilities with
advanced wear-leveling algorithms and bad block
management to significantly extend the life of the
product.
signage
displays,
test
and
measurement
instrumentation, multi-functional printers, robotics, and
video equipment and security systems.
SATA NANDrive is a single device, solid state drive
(SSD) that provides the functionality and compatibility
of a complete SATA hard disk drive (HDD) in a 14 mm
x 24 mm BGA package for easy, space saving
mounting to a system motherboard. These products
surpass traditional storage in their small size, security,
reliability, ruggedness and low power consumption.
SATA NANDrive devices are offered in a 145-ball BGA,
1 mm ball pitch package.
These specifications are subject to change without notice.
© 2019 Greenliant
07/22/2019
S71457-01
1