GLS85LS1002P / 1004P / 1008P
Industrial Grade SATA NANDrive™
Factsheet 04.100
July 2018
Features
• Industry Standard Serial ATA (SATA) Host
• Integrated Voltage Detector
Detects supply voltage fluctuations and
generates reset during power-up and power-
down to prevent inadvertent writes
• Supports SMART Commands
Interface
-
1)
-
-
-
SATA 1.5Gb/s
ATA/ATAPI-8 compliant
Supports 48-bit address feature set
• Expanded Data Protection
• Performance
-
Added data security through user-selectable
protection zones
-
Sequential data read:
Up to 70 MByte/sec*
-
Sequential data write:
Up to 60 MByte/sec*
* measured using 128 KByte transfer size
• 20-Byte Serial Number
-
-
Factory pre-programmed 10-Byte unique ID
User-programmable 10-Byte ID
• Power Management
• Robust Built-in ECC
• NAND Configuration
-
-
-
3.3V and 1.2Vpower supply
Host SATA interface power management
Immediate disabling of unused circuitry
-
1 bit per cell (SLC)
• Industrial Temperature Range
-40°C to 85°C
• FBGA package
14.0 mm x 24.0 mm x 1.95 mm, 145-ball,
1.0 mm ball pitch, FZJE
without host intervention
• Power Specifications
-
2)
-
Active mode:
-
750mW typical (GLS85LS1008P)
560mW typical (GLS85LS1004P)
450mW typical (GLS85LS1002P)
• All Devices are RoHS Compliant
-
-
Idle / Standby mode:
Sleep mode:
210mW typical
70mW typical
1) Current product revision supports SATA Revision 1.x with
host transfer rate of up to 1.5 Gb/s (i.e. SATA 1.5Gb/s).
2) For management of the Sleep Mode, refer to “SATA
NANDrive Application Design Guide.”
Product Description
The GLS85LS1002P / 1004P / 1008P Industrial Grade
SATA NANDrive™ devices (referred to as “SATA
NANDrive” in this factsheet) are fully integrated solid
state drives. They combine an advanced Greenliant
NAND controller and 2, 4 or 8 GByte of NAND flash in
a multi-chip package. These products are ideal for
embedded and portable applications that require
smaller form-factor and more reliable data storage.
The integrated NAND flash controller with built-in
advanced
NAND
management
firmware
communicates with the host through the standard
SATA protocol. It does not require any additional or
proprietary software such as the Flash File System
(FFS) and Memory Technology Driver (MTD).
SATA NANDrive is pre-programmed with a 10-Byte
unique serial ID and has the option of programming
an additional 10-Byte serial ID for even greater
system security.
SATA-interface solid state mass storage technology is
widely used in portable and industrial computers, set-
top boxes, multi-functional printers, point-of-sales
terminals, video and audio recorders, medical
instruments and car infotainment systems.
SATA NANDrive’s advanced NAND management
technology enhances data reliability and security,
improves endurance and accurately estimates the
remaining life of the NAND flash devices. This
innovative technology combines robust NAND
controller hardware error correction capabilities with
advanced wear-leveling algorithms and bad block
management to significantly extend the life of the
product.
SATA NANDrive is a single device, solid state drive
(SSD) that provides the functionality and compatibility
of a complete SATA hard disk drive (HDD) in a 14 mm
x 24 mm BGA package for easy, space saving
mounting to a system motherboard. These products
surpass traditional storage in their small size, security,
reliability, ruggedness and low power consumption.
SATA NANDrive devices are offered in a 145-ball
BGA, 1 mm ball pitch package.
These specifications are subject to change without notice.
© 2018 Greenliant
07/10/2018
S71432-F
1