5秒后页面跳转
FTW1608FE2R2MT PDF预览

FTW1608FE2R2MT

更新时间: 2024-03-03 10:09:23
品牌 Logo 应用领域
长江微电 - CJIANG /
页数 文件大小 规格书
10页 1991K
描述
铁氧体绕线

FTW1608FE2R2MT 数据手册

 浏览型号FTW1608FE2R2MT的Datasheet PDF文件第4页浏览型号FTW1608FE2R2MT的Datasheet PDF文件第5页浏览型号FTW1608FE2R2MT的Datasheet PDF文件第6页浏览型号FTW1608FE2R2MT的Datasheet PDF文件第7页浏览型号FTW1608FE2R2MT的Datasheet PDF文件第8页浏览型号FTW1608FE2R2MT的Datasheet PDF文件第10页 
a. Accordingly increasing the solder volume, the mechanical stress to chip is also increased.Exceeding solder volume may cause the  
failure of mechanical or electrical performance.  
b. Before soldering, please ensure that the solder should not adhere to the wire part of chip.  
c. Please pay particular attention to whether there is flux remaining on surface of the wire part of chip after subjected to reflow soldering  
since this may causing short circuit of parts.  
11. Cleaning  
Products shall be cleaned on the following conditions:  
a. Cleaning temperature shall be limited to 60Max. (40Max. for fluoride and alcohol type cleaner.)  
b. Ultrasonic cleaning shall comply with the following conditions, avoiding the resonance phenomenon at the mounted products and  
PCB.  
Power: 20W/l Max.  
Frequency: 28 KHz to 40 KHz  
Time: 5 minutes Max  
c. Cleaner  
i.  
Alternative cleaner  
z
Isopropyl alcohol (IPA)  
HCFC-225  
z
ii.  
Aqueous agent  
z
Surface Active Agent Type (Clean through-750H)  
Hydrocarbon Type (Techno Cleaner-335)  
Higher Alcohol Type (Pine Alpha ST-100S)  
Alkali saponifier Type (Aqua Cleaner 240)  
z
z
z
Alkali saponification shall be diluted to 20% volume with de-ionized water.  
Please contact our technical service department before using other cleaner.  
d. There shall be no residual flux and residual cleaner after cleaning. In the case of using aqueous agent, product shall be dried  
completely after rinse with de-ionized water in order to remove the cleaner.  
e. Some products may become slightly whitened. However, product performance or usage is not affected.  
f.  
Please take care of winding part while cleaning.  
g. After cleaning, parts could be subjected to the next reflow soldering till the solvent remaining on surface of parts being volatilized.  
12. Others  
a. We will not inform you of the improvement on specification of parts in advance.  
b. We will not inform you of the change on specification of parts during design in advance.  
c. Please contact us for the date to realize mass production of parts being designed.  
Specifications subject to change without notice. Please check our website for latest informations.  
WWW.CJIANG.TW  

与FTW1608FE2R2MT相关器件

型号 品牌 获取价格 描述 数据表
FTW1608FE4R7KT CJIANG

获取价格

铁氧体绕线
FTW1608FE6R8KT CJIANG

获取价格

铁氧体绕线
FTW1608FE6R8MT CJIANG

获取价格

铁氧体绕线
FTW-17-02-G-S-H SAMTEC

获取价格

Board Connector, 17 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Solder Termina
FTW-17-02-G-S-H-SM SAMTEC

获取价格

Board Connector, 17 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Black Insulato
FTW-17-02-T-D-H-SM SAMTEC

获取价格

Board Connector, 34 Contact(s), 2 Row(s), Male, Straight, 0.079 inch Pitch, Black Insulato
FTW-17-02-T-D-L SAMTEC

获取价格

Board Connector, 34 Contact(s), 2 Row(s), Male, Straight, 0.079 inch Pitch, Solder Termina
FTW-17-02-T-S-H SAMTEC

获取价格

Board Connector, 17 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Solder Termina
FTW-17-03-T-S-L SAMTEC

获取价格

Board Connector, 17 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Solder Termina
FTW-17-04-G-S-H SAMTEC

获取价格

Board Connector, 17 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Solder Termina