®
Bussmann
®
Fusetron
FRS-R
⁄Ω¡º-60A
Dual-Element, Time-Delay Fuses
Class RK5 – 600 Volt
General Information:
Dimensional Data
• Provides motor overload, ground fault and short-circuit pro-
tection. When used in circuits subject to surge currents such
as those caused by motors, transformers and other inductive
components, these fuses can be sized close to full-load
amperes to give maximum overcurrent protection.
• Permits the use of smaller and less costly switches. The time-
delay feature makes it possible to use fuse ampere ratings
which are much smaller than those of non-time-delay fuses.
Considerable cost saving occurs by permitting the use of
smaller size switches, panels and fuses themselves.
• Provides a higher degree of short-circuit protection (greater
current-limitation) in circuits in which surge currents or tempo-
rary overloads occur.
5" (± 0.31)
.81" (± 0.008)
⁄Ω¡ºA to 30A
5.5" (± 0.31)
1.06" (± 0.008)
35A to 60A
• Helps protect motors against burnout from overloads.
• Gives motor running back-up protection to motors without
extra costs.
• Helps protect motors against burnout from single phasing on
three phase systems.
Catalog Symbol: FRS-R
Dual-Element, Time-Delay – 10 second (minimum) at 500%
rated current
Current-Limiting
Ampere Rating: ⁄Ω¡º to 60 Amperes
Voltage Rating: 600 Volts AC (or less)
Interrupting Rating: 200,000A RMS Sym.
DC Ratings (20,000AIC @ 250 VDC)
Agency Approvals:
• Simplifies and improves blackout prevention (selective
coordination).
• Dual-element fuses can be applied in circuits subject to tem-
porary motor overloads and surge currents to provide both
high-performance, short-circuit and overload protection.
• The overload element provides protection against low level
overcurrent of overloads and will hold an overload which is
five times greater than the ampere rating of the fuse for a
minimum of ten seconds.
UL Listed, Std. 248-12, Class RK5, Guide JDDZ, File E4273
CSA Certified, C22.2 No. 248.12, Class 1422-02, File 53787
Catalog Numbers
FRS-R-⁄Ω¡º
FRS-R-1°Ω¡º
FRS-R-2
FRS-R-8
FRS-R-9
FRS-R-10
FRS-R-12
FRS-R-15
FRS-R-17⁄Ω™
FRS-R-20
FRS-R-25
FRS-R-30
FRS-R-35
FRS-R-40
FRS-R-45
FRS-R-50
FRS-R-60
—
FRS-R-⁄Ω•
FRS-R-⁄fiΩ¡ºº
FRS-R-¤Ω¡º
FRS-R-⁄Ω¢
FRS-R-2⁄Ω¢
FRS-R-2⁄Ω™
FRS-R-2°Ω¡º
FRS-R-3
Fuse Reducers For Class R Fuses
Desired
Fuse (Case)
Size
Catalog Number
(Pairs)
Equipment
Fuse Clips
600V
FRS-R-‹Ω¡º
FRS-R-›Ω¡º
FRS-R-⁄Ω™
60A
30A
30A
60A
60A
No. 663-R
No. 216-R
No. 616-R
No. 626-R
FRS-R-3¤Ω¡º
FRS-R-3⁄Ω™
FRS-R-4
100A
FRS-R-flꭧ
FRS-R-°Ω¡º
FRS-R-1
200A
FRS-R-4⁄Ω™
FRS-R-5
FRS-R-1⁄Ω•
FRS-R-1⁄Ω¢
FRS-R-1›Ω¡º
FRS-R-1⁄Ω™
FRS-R-1flꭧ
FRS-R-5flꭧ
FRS-R-6
Class R Catalog Numbers
(Clip Retaining Spring Standard, Suffix “R”)
FRS-R-6⁄Ω¢
FRS-R-7
Terminal Type (Suffix No.)
Screw w/ Box Lug w/
Basic
Catalog
Poles Number
FRS-R-7⁄Ω™
—
—
Pres.
Plate
PR
—
Clip
CU only
COR
Amps
⁄Ω¡º
Carton Quantity and Weight
1
2
3
1
2
3
R60030-1
R60030-2
R60030-3
R60060-1
R60060-2
R60060-3
SR
SR
SR
SR
SR
SR
CR
CR
CR
CR
CR
CR
Weight*
Ampere
Ratings
Carton
Qty.
to
PR
PR
—
COR
COR
COR
COR
COR
Lbs.
0.40
0.50
3.10
Kg.
30
31
to
⁄Ω¡º–15
10
10
10
0.181
0.277
1.406
17.5–30
—
35-60
60
—
*Weight per carton.
CE logo denotes compliance with European Union Low Voltage Directive
(50-1000 VAC, 75-1500 VDC). Refer to BIF document #8002 or contact
Bussmann Application Engineering at 314-527-1270 for more information.
Form No. FRS-R 1/10-60
12-17-98
Page 1 of 2
SB98107
BIF Doc #1017
Rev. A