Low Voltage, CMOS Multimedia Switch
ADG790
FUNCTIONAL BLOCK DIAGRAM
ADG790
FEATURES
Single-chip audio/video/data switching solution
Wide bandwidth section
Rail-to-rail signal switching capability
Compliant with full speed USB 2.0 signaling (3.6 V p-p)
Compliant with high speed USB 2.0 signaling (400 mV p-p)
Supports USB data rates up to 480 Mbps
550 MHz, 3 dB bandwidth
Low RON: 5.9 Ω typical
Excellent matching between channels
Low distortion section
Low RON: 3.9 Ω typical
230 MHz, 3 dB bandwidth (SPDT)
160 MHz, 3 dB bandwidth (4:1 multiplexers)
Single-supply operation: 1.65 V to 3.6 V
Typical power consumption: <0.1 μW
Pb-free packaging: 30-ball WLCSP (3 mm × 2.5 mm)
WIDE
BANDWIDTH
SECTION
LOW
DISTORTION
SECTION
S5A
S5B
S5C
S5D
D5
S1A
S1B
D1
S6A
S2A
S2B
D2
S6B
S6C
S6D
D6
S3A
S3B
D3
S4A
S4B
D4
APPLICATIONS
DECODER
Cellular phones
PMPs
MP3 players
V
IN1 IN2 IN3 S/D GND
DD
Audio/video/data/USB switching
Figure 1.
GENERAL DESCRIPTION
The ADG790 is a single-chip, CMOS switching solution that
comprises four SPDT switches and two 4:1 multiplexers. The
internal architecture of the device provides two switching
sections, a wide bandwidth section and a low distortion section.
All switches conduct equally well in both directions when on
and block signals up to the supply rails when off. A 4-wire
parallel interface controls the operation of the device and
allows the user to control switches from both sections simul-
taneously. This simplifies the design and provides a cost-effective,
single-chip switching solution for portable devices where
multiple signals share a single port connector. The shutdown
(S/D) pin allows the user to disable all four SPDT switches and
force the 4:1 multiplexers into the S5B and S6B positions,
respectively.
The wide bandwidth section contains three SPDT switches that
exhibit low on resistance with excellent flatness and channel
matching. This, combined with wide bandwidth, makes the
three-SPDT-switch configuration ideal for high frequency
signals, such as full speed (12 Mbps) and high speed (480 Mbps)
USB signals and high resolution video signals.
The ADG790 is packaged in a compact, 30-ball WLCSP (6 × 5
ball array) with a total area of 7.5 mm2 (3 mm × 2.5 mm). This
tiny package size and its low power consumption make the
ADG790 an ideal solution for portable devices.
The low distortion section contains a single SPDT switch and
two 4:1 multiplexers that exhibit very low on resistance and
excellent flatness, making these switches ideal for a wide range
of applications, including low distortion audio applications and
low resolution video (CVBS and S-Video) applications.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2007 Analog Devices, Inc. All rights reserved.