Aluminum Electrolytic Capacitor/TG
Surface Mount Type
Series: TG
■ Features
Type :
V
Japan
Endurance:125°C 1000 to 2000 h
Miniaturization(40% less than TA Series)
Low ESR(Low temp)
<
Vibration-proof product is available upon request.(φ8
)
=
Corresponds to use in the car engine room.
The best for an electronically controlled
unit (ECU, ABS etc).
■ Application
■ Specifications
Category temp. range
Rated W.V. Range
Nominal Cap. Range
Capacitance Tolerance
DC Leakage Current
tan δ
-40 to +125°C
10 to 100 V .DC
10 to 4700 µ F
±20 % (120Hz/+20°C)
<= 0.01 CV or 3(µ A) after 2 minutes (whichever, greater)
I
Please see the attached standard products list
W.V. (V)
10
16
25
35
50
63
80
100
Characteristics
at Low Temperature
(Inpedance ratio at 120Hz)
<
-25 / +20 °C
-40 / +20 °C
3
6
2
4
2
4
2
3
2
3
2
3
2
3
2
3
After applying rated working voltage for 1000 hours(φ8x6.2), 2000 hours(8x10.2 ) at +125
=
±2°C and then being stabilized at +20°C, capacitors shall meet the following limits.
Endurance
Shelf Life
±30 % of initial measured value (code U:±35%)
<=300 % of initial specified value (code U:350%)
<= initial specified value
Capacitance change
tan δ
DC leakage current
After storage for 1000 hours at +125±2°C with no voltage applied and then being stabilized
at +20°C, capacitors shall meet the limits specified in Endurance.(With voltage treatment)
After reflow soldering ( Refer to page 20 for recommendable temperature profile.) and then
being stabilized at +20°C, capacitor shall meet the following limits.
Resistance to
Soldering Heat
±10 % of initial measured value
<= initial specified value
<= initial specified value
Capacitance change
tan δ
DC leakage current
■ Dimensions in mm (not to scale)
■ Marking
( ) reference size
<
( φ10)
=
W.V. code
A±0.2
0.3 max
Capacitance
(µF)
Negative polarity
marking
Series
identification
TG
Lot number
w
E~G=L±0.3
H~K=L±0.5
>
W.V. code
( φ12.5)
=
Capacitance
(µF)
Negative polarity
marking
Size
D
L
A,B H max.
8.0 6.2 8.3 9.5 3.4 0.65 ±0.1 2.2 0.35
8.0 10.2 8.3 10.0 3.4 0.90 ±0.2 3.1 0.70
I
W
P
K
TG
Series
identification
code
E
-0.20 to +0.15
±0.20
F
Lot number
±0.20
±0.30
±0.30
±0.30
G
10.0 10.2 10.3 12.0
3.5 0.90 ±0.2 4.6 0.70
W.V. code
V
H13
J16
K16
12.5 13.5 13.5 15.0 4.7 0.90 ±0.3 4.4 0.70
16.0 16.5 17.0 19.0 5.5 1.20±0.3 6.7 0.70
18.0 16.5 19.0 21.0 6.7 1.20 ±0.3 6.7 0.70
10 16
25 35
Code
A
C
E
V
V
50
H
63 80 100
2A
Code
J
K
Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use.
Whenever a doubt about safety arises from this product, please inform us immediately for technical consulation without fail.
EE74