dsPIC33EPXXXGM3XX/6XX/7XX
16-Bit Digital Signal Controllers with High-Speed PWM,
Op Amps and Advanced Analog Features
Operating Conditions
Timers/Output Compare/Input Capture
• 3.0V to 3.6V, -40°C to +85°C, up to 70 MIPS
• 3.0V to 3.6V, -40°C to +125°C, up to 60 MIPS
• 21 General Purpose Timers:
- Nine 16-bit and up to four 32-bit timers/counters
- Eight output capture modules configurable as
timers/counters
Core: 16-Bit dsPIC33E CPU
• Code-Efficient (C and Assembly) Architecture
• Two 40-Bit Wide Accumulators
• Single-Cycle (MAC/MPY) with Dual Data Fetch
• Single-Cycle Mixed-Sign MUL plus Hardware Divide
• 32-Bit Multiply Support
- PTG module with two configurable timers/counters
- Two 32-bit Quadrature Encoder Interface (QEI)
modules configurable as a timer/counter
• Eight Input Capture modules
• Peripheral Pin Select (PPS) to allow Function Remap
• Peripheral Trigger Generator (PTG) for Scheduling
Complex Sequences
Clock Management
• Internal Fast FRC Oscillator with 1% Accuracy
• Programmable PLLs and Oscillator Clock Sources
• Fail-Safe Clock Monitor (FSCM)
• Independent Watchdog Timer (WDT)
• Fast Wake-up and Start-up
Communication Interfaces
• Four Enhanced Addressable UART modules
(17.5 Mbps):
- With support for LIN/J2602 protocols and IrDA®
• Three 3-Wire/4-Wire SPI modules (15 Mbps)
• 25 Mbps Data Rate for Dedicated SPI module
(with no PPS)
Power Management
• Low-Power Management modes (Sleep, Idle, Doze)
• Executing Optimized NOPString with Flash Fetch
• Integrated Power-on Reset and Brown-out Reset
• 0.6 mA/MHz Dynamic Current (typical)
2
• Two I C™ modules (up to 1 Mbps) with SMBus Support
• Two CAN modules (1 Mbps) with CAN 2.0B Support
• Programmable Cyclic Redundancy Check (CRC)
• Codec Interface module (DCI) with I S Support
2
• 30 µA IPD Current (typical)
High-Speed PWM
Direct Memory Access (DMA)
• Up to 12 PWM Outputs (six generators)
• Primary Master Time Base Inputs allow Time Base
Synchronization from Internal/External Sources
• Dead Time for Rising and Falling Edges
• 7.14 ns PWM Resolution
• 4-Channel DMA with User-Selectable Priority Arbitration
• Peripherals Supported by the DMA Controller include:
- UART, SPI, ADC, CAN and input capture
- Output compare and timers
Input/Output
• PWM Support for:
- DC/DC, AC/DC, Inverters, PFC, Lighting
- BLDC, PMSM, ACIM, SRM
• Sink/Source 15 mA or 10 mA, Pin-Specific for
Standard VOH/VOL
• Programmable Fault Inputs
• 5V Tolerant Pins
• Flexible Trigger Configurations for ADC Conversions
• Supports PWM Lock, PWM Output Chopping and
Dynamic Phase Shifting
• Selectable Open-Drain, Pull-ups and Pull-Downs
• Up to 5 mA Overvoltage Clamp Current
• Change Notice Interrupts on All I/O Pins
• PPS to allow Function Remap
Advanced Analog Features
• Two Independent ADC modules:
Qualification and Class B Support
- Configurable as 10-bit, 1.1 Msps with
four S&H or 12-bit, 500 ksps with one S&H
- 11, 13, 18, 30 or 49 analog inputs
• AEC-Q100 REVG (Grade 1, -40°C to +125°C) Planned
• AEC-Q100 REVG (Grade 0, -40°C to +150°C) Planned
• Class B Safety Library, IEC 60730
• Flexible and Independent ADC Trigger Sources
• Up to Four Op Amp/Comparators with Direct
Connection to the ADC module:
Debugger Development Support
• In-Circuit and In-Application Programming
• Three Complex and Five Simple Breakpoints
• IEEE 1149.2 Compatible (JTAG) Boundary Scan
• Trace and Run-Time Watch
- Additional dedicated comparator
- Programmable references with 32 voltage points
- Programmable blanking and filtering
• Charge Time Measurement Unit (CTMU):
- Supports mTouch™ capacitive touch sensing
- Provides high-resolution time measurement (1 ns)
- On-chip temperature measurement
2013-2014 Microchip Technology Inc.
DS70000689D-page 1